/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support
 * ----------------------------------------------------------------------------
 * Copyright (c) 2008, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/// \file

//------------------------------------------------------------------------------
//         Headers
//------------------------------------------------------------------------------

#include "pio.h"
#include <board.h>
#include <pmc/pmc.h>

//------------------------------------------------------------------------------
//         Local Functions
//------------------------------------------------------------------------------

//------------------------------------------------------------------------------
/// Configures one or more pin(s) of a PIO controller as being controlled by
/// peripheral A. Optionally, the corresponding internal pull-up(s) can be
/// enabled.
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask of one or more pin(s) to configure.
/// \param enablePullUp  Indicates if the pin(s) internal pull-up shall be
///                      configured.
//------------------------------------------------------------------------------
static void PIO_SetPeripheralA(
    Pio *pio,
    unsigned int mask,
    unsigned char enablePullUp)
{
    unsigned int abcdsr;
    // Disable interrupts on the pin(s)
    pio->PIO_IDR = mask;

    // Enable the pull-up(s) if necessary
    if (enablePullUp) {
        pio->PIO_PUER = mask;
    }
    else {

        pio->PIO_PUDR = mask;
    }
    
    abcdsr = pio->PIO_ABCDSR[0];
    pio->PIO_ABCDSR[0] &= (~mask & abcdsr);
    abcdsr = pio->PIO_ABCDSR[1];
    pio->PIO_ABCDSR[1] &= (~mask & abcdsr);
    pio->PIO_PDR = mask;
}

//------------------------------------------------------------------------------
/// Configures one or more pin(s) of a PIO controller as being controlled by
/// peripheral B. Optionally, the corresponding internal pull-up(s) can be
/// enabled.
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask of one or more pin(s) to configure.
/// \param enablePullUp  Indicates if the pin(s) internal pull-up shall be
///                      configured.
//------------------------------------------------------------------------------
static void PIO_SetPeripheralB(
    Pio *pio,
    unsigned int mask,
    unsigned char enablePullUp)
{
    unsigned int abcdsr;
    // Disable interrupts on the pin(s)
    pio->PIO_IDR = mask;

    // Enable the pull-up(s) if necessary
    if (enablePullUp) {

        pio->PIO_PUER = mask;
    }
    else {

        pio->PIO_PUDR = mask;
    }

    abcdsr = pio->PIO_ABCDSR[0];
    pio->PIO_ABCDSR[0] = (mask | abcdsr);
    abcdsr = pio->PIO_ABCDSR[1];
    pio->PIO_ABCDSR[1] &= (~mask & abcdsr);
    
    pio->PIO_PDR = mask;
}

//------------------------------------------------------------------------------
/// Configures one or more pin(s) of a PIO controller as being controlled by
/// peripheral C. Optionally, the corresponding internal pull-up(s) can be
/// enabled.
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask of one or more pin(s) to configure.
/// \param enablePullUp  Indicates if the pin(s) internal pull-up shall be
///                      configured.
//------------------------------------------------------------------------------
static void PIO_SetPeripheralC(
    Pio *pio,
    unsigned int mask,
    unsigned char enablePullUp)
{
    unsigned int abcdsr;
    // Disable interrupts on the pin(s)
    pio->PIO_IDR = mask;

    // Enable the pull-up(s) if necessary
    if (enablePullUp) {

        pio->PIO_PUER = mask;
    }
    else {

        pio->PIO_PUDR = mask;
    }

    abcdsr = pio->PIO_ABCDSR[0];
    pio->PIO_ABCDSR[0] &= (~mask & abcdsr);
    abcdsr = pio->PIO_ABCDSR[1];
    pio->PIO_ABCDSR[1] = (mask | abcdsr);
    
    pio->PIO_PDR = mask;
}

//------------------------------------------------------------------------------
/// Configures one or more pin(s) of a PIO controller as being controlled by
/// peripheral D. Optionally, the corresponding internal pull-up(s) can be
/// enabled.
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask of one or more pin(s) to configure.
/// \param enablePullUp  Indicates if the pin(s) internal pull-up shall be
///                      configured.
//------------------------------------------------------------------------------
static void PIO_SetPeripheralD(
    Pio *pio,
    unsigned int mask,
    unsigned char enablePullUp)
{
    unsigned int abcdsr;
    // Disable interrupts on the pin(s)
    pio->PIO_IDR = mask;

    // Enable the pull-up(s) if necessary
    if (enablePullUp) {

        pio->PIO_PUER = mask;
    }
    else {

        pio->PIO_PUDR = mask;
    }

    abcdsr = pio->PIO_ABCDSR[0];
    pio->PIO_ABCDSR[0] = (mask | abcdsr);
    abcdsr = pio->PIO_ABCDSR[1];
    pio->PIO_ABCDSR[1] = (mask | abcdsr);
    
    pio->PIO_PDR = mask;
}

//------------------------------------------------------------------------------
/// Configures one or more pin(s) or a PIO controller as inputs. Optionally,
/// the corresponding internal pull-up(s) and glitch filter(s) can be
/// enabled.
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask indicating which pin(s) to configure as input(s).
/// \param enablePullUp  Indicates if the internal pull-up(s) must be enabled.
/// \param enableFilter  Indicates if the glitch filter(s) must be enabled.
//------------------------------------------------------------------------------
static void PIO_SetInput(
    Pio *pio,
    unsigned int mask,
    unsigned char attribute)
{
    // Disable interrupts
    pio->PIO_IDR = mask;

    // Enable pull-up(s) if necessary
    if (attribute & PIO_PULLUP)
        pio->PIO_PUER = mask;
    else
        pio->PIO_PUDR = mask;

    // Enable de-glitch(s) if necessary
    if (attribute & PIO_DEGLITCH)
        pio->PIO_IFER = mask;
    else
        pio->PIO_IFDR = mask;

    // Enable de-bounce if necessary
    if (attribute & PIO_DEBOUNCE) {
        pio->PIO_DIFSR = mask;
    }

    // Configure pin as input
    pio->PIO_ODR = mask;
    pio->PIO_PER = mask;
}

//------------------------------------------------------------------------------
/// Configures one or more pin(s) of a PIO controller as outputs, with the
/// given default value. Optionally, the multi-drive feature can be enabled
/// on the pin(s).
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask indicating which pin(s) to configure.
/// \param defaultValue  Default level on the pin(s).
/// \param enableMultiDrive  Indicates if the pin(s) shall be configured as
///                          open-drain.
/// \param enablePullUp  Indicates if the pin shall have its pull-up activated.
//------------------------------------------------------------------------------
static void PIO_SetOutput(
    Pio *pio,
    unsigned int mask,
    unsigned char defaultValue,
    unsigned char enableMultiDrive,
    unsigned char enablePullUp)
{
    // Disable interrupts
    pio->PIO_IDR = mask;

    // Enable pull-up(s) if necessary
    if (enablePullUp) {

        pio->PIO_PUER = mask;
    }
    else {

        pio->PIO_PUDR = mask;
    }

    // Enable multi-drive if necessary
    if (enableMultiDrive) {

        pio->PIO_MDER = mask;
    }
    else {

        pio->PIO_MDDR = mask;
    }

    // Set default value
    if (defaultValue) {

        pio->PIO_SODR = mask;
    }
    else {

        pio->PIO_CODR = mask;
    }

    // Configure pin(s) as output(s)
    pio->PIO_OER = mask;
    pio->PIO_PER = mask;
}

//------------------------------------------------------------------------------
/// Configures interrupt mode for input Pins
/// \param pio  Pointer to a PIO controller.
/// \param mask  Bitmask indicating which pin(s) to configure.
/// \param additionnalItMode  Enable Pio Additionnal It Mode.
/// \param edgeMode  Enable the edge mode.
/// \param risingEdgeOrHighLevel  Enable IT on rising edge or high level.
//------------------------------------------------------------------------------
static void PIO_SetInterrupt(
    Pio *pio,
    unsigned int mask,
    unsigned char additionnalItMode,
    unsigned char edgeMode,
    unsigned char risingEdgeOrHighLevel)
{
    /* Configure the Interrupt mode in the PIO controller */
    if (additionnalItMode) {
        /* enable additional interrupt mode */
        pio->PIO_AIMER       = mask;
        
        /* if bit field of selected pin is 1, set as Rising Edge/High level detection event */
        if (risingEdgeOrHighLevel)
            pio->PIO_REHLSR    = mask;
        else
            pio->PIO_FELLSR     = mask;

        /* if bit field of selected pin is 1, set as edge detection source */
        if (edgeMode)
            pio->PIO_ESR     = mask;
        else
            pio->PIO_LSR     = mask;
    } else {
        /* disable additional interrupt mode */
        pio->PIO_AIMDR       = mask;
    }
}

//------------------------------------------------------------------------------
//         Global Functions
//------------------------------------------------------------------------------

//------------------------------------------------------------------------------
/// Configures a list of Pin instances, each of which can either hold a single
/// pin or a group of pins, depending on the mask value; all pins are configured
/// by this function. The size of the array must also be provided and is easily
/// computed using PIO_LISTSIZE whenever its length is not known in advance.
/// \param list  Pointer to a list of Pin instances.
/// \param size  Size of the Pin list (calculated using PIO_LISTSIZE).
/// \return 1 if the pins have been configured properly; otherwise 0.
//------------------------------------------------------------------------------
unsigned char PIO_Configure(const Pin *list, unsigned int size)
{
    // Configure pins
    while (size > 0) {

        switch (list->type) {

            case PIO_PERIPH_A:
                PIO_SetPeripheralA(list->pio,
                                   list->mask,
                                   (list->attribute & PIO_PULLUP) ? 1 : 0);
                break;

            case PIO_PERIPH_B:
                PIO_SetPeripheralB(list->pio,
                                   list->mask,
                                   (list->attribute & PIO_PULLUP) ? 1 : 0);
                break;

            case PIO_PERIPH_C:
                PIO_SetPeripheralC(list->pio,
                                   list->mask,
                                   (list->attribute & PIO_PULLUP) ? 1 : 0);
                break;
                
            case PIO_PERIPH_D:
                PIO_SetPeripheralD(list->pio,
                                   list->mask,
                                   (list->attribute & PIO_PULLUP) ? 1 : 0);
                break;
            case PIO_INPUT:
                PMC_EnablePeripheral(list->id);
                PIO_SetInput(list->pio,
                             list->mask,
                             list->attribute);
                PIO_SetInterrupt(list->pio,
                                 list->mask,
                                 (list->attribute & PIO_IT_AIME) ? 1 : 0,
                                 (list->attribute & PIO_IT_EDGE) ? 1 : 0,
                                 (list->attribute & PIO_IT_RE_OR_HL) ? 1 : 0);
                break;

            case PIO_OUTPUT_0:
            case PIO_OUTPUT_1:
                PIO_SetOutput(list->pio,
                              list->mask,
                              (list->type == PIO_OUTPUT_1),
                              (list->attribute & PIO_OPENDRAIN) ? 1 : 0,
                              (list->attribute & PIO_PULLUP) ? 1 : 0);
                break;

            default: return 0;
        }
                         
        list++;
        size--;
    }

    return 1;
}

//------------------------------------------------------------------------------
/// Sets a high output level on all the PIOs defined in the given Pin instance.
/// This has no immediate effects on PIOs that are not output, but the PIO
/// controller will memorize the value they are changed to outputs.
/// \param pin  Pointer to a Pin instance describing one or more pins.
//------------------------------------------------------------------------------
void PIO_Set(const Pin *pin)
{
    pin->pio->PIO_SODR = pin->mask;
}

//------------------------------------------------------------------------------
/// Sets a low output level on all the PIOs defined in the given Pin instance.
/// This has no immediate effects on PIOs that are not output, but the PIO
/// controller will memorize the value they are changed to outputs.
/// \param pin  Pointer to a Pin instance describing one or more pins.
//------------------------------------------------------------------------------
void PIO_Clear(const Pin *pin)
{
    pin->pio->PIO_CODR = pin->mask;
}

//------------------------------------------------------------------------------
/// Returns 1 if one or more PIO of the given Pin instance currently have a high
/// level; otherwise returns 0. This method returns the actual value that is
/// being read on the pin. To return the supposed output value of a pin, use
/// PIO_GetOutputDataStatus() instead.
/// \param pin  Pointer to a Pin instance describing one or more pins.
/// \return 1 if the Pin instance contains at least one PIO that currently has
/// a high level; otherwise 0.
//------------------------------------------------------------------------------
unsigned char PIO_Get(const Pin *pin)
{
    unsigned int reg;
    if ((pin->type == PIO_OUTPUT_0) || (pin->type == PIO_OUTPUT_1)) {

        reg = pin->pio->PIO_ODSR;
    }
    else {

        reg = pin->pio->PIO_PDSR;
    }

    if ((reg & pin->mask) == 0) {

        return 0;
    }
    else {

        return 1;
    }
}


//------------------------------------------------------------------------------
/// Returns 1 if one or more PIO of the given Pin are configured to output a
/// high level (even if they are not output).
/// To get the actual value of the pin, use PIO_Get() instead.
/// \param pin  Pointer to a Pin instance describing one or more pins.
/// \return 1 if the Pin instance contains at least one PIO that is configured
/// to output a high level; otherwise 0.
//------------------------------------------------------------------------------
unsigned char PIO_GetOutputDataStatus(const Pin *pin)
{
    if ((pin->pio->PIO_ODSR & pin->mask) == 0) {

        return 0;
    }
    else {

        return 1;
    }
}