#include "peekpoke.h"
#include<unistd.h>
#include<sys/types.h>
#include<sys/mman.h>
#include<stdio.h>
#include<fcntl.h>
#include<assert.h>
#include<time.h>

/*Register addresses */ 
#define CHIP_SELECT_PAGE 0x80840000UL
#define SSP_PAGE         0x808A0000UL

/*Offsets*/
#define SSPCR1           0x04
#define SSPCPSR          0x10
#define CHIP_SELECT_DATA 0x30
#define CHIP_SELECT_DDR  0x34
#define SSP_DATA         0x08

#define TRUE  0
#define FALSE !TRUE


int main(int argc, char **argv) 
{
	unsigned long val;
	double temp;
	volatile unsigned char *chip_select_page, *ssp_page;
	unsigned char isNegative = FALSE;
	
	int fd = open("/dev/mem", O_RDWR|O_SYNC);
	assert(fd != -1);
	
	/* this program has 2 seconds to complete or it will be killed */
	alarm(2);

	/* Lets intialize our pointers */
	chip_select_page = mmap(0, getpagesize(), PROT_READ|PROT_WRITE, MAP_SHARED, fd, CHIP_SELECT_PAGE);
	assert(chip_select_page != MAP_FAILED);

	ssp_page = mmap(0, getpagesize(), PROT_READ|PROT_WRITE, MAP_SHARED, fd, SSP_PAGE);
	assert(ssp_page != MAP_FAILED);

	/* 
	 The EP9301 Users Manual says the following algorithm must 
	 be used to configure and enable the SPI bus
	 http://www-s.ti.com/sc/ds/tmp124.pdf
	*/

	/* 1.)	Set enable bit(SSE) in register SSPCR1*/
	POKE32( (unsigned long)(ssp_page + SSPCR1), 0x10 );
	
	/* 2.)	Write other SSP config registers(SSPCR0 & SSPCPSR)*/
	POKE32( (unsigned long)ssp_page, 0x0F ); 
	POKE32( (unsigned long)(ssp_page + SSPCPSR), 0xFE ); 

	/* 3.)	Clear the enable bit(SSE) in register SSPCR1*/
	POKE32( (unsigned long)(ssp_page + SSPCR1), 0x00 ); 
	//usleep(10000); //let the lines settle
	
	/* 4.)	Set the enable bit(SSE) in register SSPCR1*/
	POKE32( (unsigned long)(ssp_page + SSPCR1), 0x10 ); 

	/* Done with configuration now lets read the current temp...*/

	//enable the chip select
	POKE32( (unsigned long)(chip_select_page + CHIP_SELECT_DDR), 0x04 ); 
	POKE32( (unsigned long)(chip_select_page + CHIP_SELECT_DATA), 0x00 ); 


	//send read temp command
	POKE32( (unsigned long)(ssp_page + SSP_DATA), 0x8000 ); 
	usleep(1000);	

	//disable chip select
	POKE32( (unsigned long)(chip_select_page + CHIP_SELECT_DDR), 0x00 ); 

	//read the temp
	val = PEEK32( (unsigned long)(ssp_page + SSP_DATA) );

	//Lets check if the value is negative
	if( val <= 0xFFFF && val >= 0xE487 )
	{
		//perform two's complement
		val = ~val + 1;
		isNegative = TRUE;

	} else if( val <= 0x4B08 && val >= 0xE486 ) 
	{
		printf("FAIL, invalid register value(out of range)...\n");
		return 2;
	}

	if( val >= 0x3E88 && val <= 0x4B07)
	{
		temp = val / 128.046;

	} else if( val >= 0xC88 && val <= 0x3E87 )
	{
		temp = val / 128.056;

	} else if( val >= 0x10 && val <= 0xC87 )
	{
		temp = val / 128.28;
	} else// => val >= 0x00 && val <= 0x0F 
	{
		temp = val / 240;
	} 

	//convert the temp to farenheit
	printf("\nThe temp is: %3.2f degrees Celcius\n", temp);
	temp = (temp * 1.8) + 32;
	printf("The temp is: %3.2f degrees Farenheit\n", temp);

	return 0;
	
}