analog Channel 0 = 55466 counts 2.12 volts 25.623 Batt Volts Channel 1 = 54610 counts 2.08 volts 25.228 Batt Volts Channel 2 = 6697 counts 0.26 volts 0.274 bar Channel 3 = 14498 counts 0.55 volts 15.153 psia Channel 4 = 18664 counts 0.71 volts 21.198 degC Channel 5 = 23801 counts 0.91 volts 19.012 % BEDS)>type beds.cfg #START 10/4/2015 18:00:00 platformID = 3 ModemAddr = 3 deploymentID = 2 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 240 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)> BEDS)>deletechar 1 beds.cfg BEDS)>type beds.cfg START 10/4/2015 18:00:00 platformID = 3 ModemAddr = 3 deploymentID = 2 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 240 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>reset This could cause permanent loss of communication. Are you really sure [N] ? user:32> OK user:33> CONNECT 00800 bits/sec user:34> Response Not Received user:35> Response Not Received user:36> user:36> Response Not Received user:37> user:37> Response Not Received user:38> Response Not Received user:39> user:39> Response Not Received user:40> Response Not Received user:41> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=004 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=005 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:42> OK user:43> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=004 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=004 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:44> CONNECT 00800 bits/sec user:45> Response Not Received user:46> Command '+++aatr4' not found Error user:47> Response Not Received user:48> Response Not Received user:49> CONNECT 00800 bits/sec user:50> OK user:51> Response Not Received user:52> Response Not Received user:53> CONNECT 00800 bits/sec user:54> OK user:55> Response Not Received user:56> user:56> CONNECT 00800 bits/sec BEDS)> BEDS)>event Event Start Time Duration Max G File Name BEDS)>analog Channel 0 = 57747 counts 2.20 volts 26.677 Batt Volts Channel 1 = 57791 counts 2.20 volts 26.697 Batt Volts Channel 2 = 6620 counts 0.25 volts 0.127 bar Channel 3 = 14680 counts 0.56 volts 15.500 psia Channel 4 = 18650 counts 0.71 volts 21.144 degC Channel 5 = 27804 counts 1.06 volts 26.216 % BEDS)>type beds.cfg #START 10/4/2015 18:00:00 platformID = 6 ModemAddr = 6 deploymentID = 1 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 600 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>deletechar 1 beds.cfg Privilege violation BEDS)>pro iv 100 Setting command parser privilege to 100 BEDS)>deletechar 1 beds.cfg BEDS)>type beds.cfg START 10/4/2015 18:00:00 platformID = 6 ModemAddr = 6 deploymentID = 1 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 600 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>reset This could cause permanent loss of communication. Are you really sure [N] ? user:57> Response Not Received user:58> Remote Sregisters S00=042 S01=000 S02=000 S03=002 S04=005 S05=000 S06=006 S07=015 S08=010 S09=000 S10=036 S11=000 S12=000 S13=000 S14=000 S15=001 S16=001 S17=001 S18=006 S19=000 S20=000 user:59> user:59> OK user:60> CONNECT 00800 bits/sec BEDS)> BEDS)>ype beds.cfg Bad command or file name BEDS)>type beds.cfg START 10/4/2015 18:00:00 platformID = 6 ModemAddr = 6 deploymentID = 1 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 600 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>type Not found error BEDS)> BEDS)>type syslog.txt 2015/10/05 14:53:44.752, SysLog started 2015/10/05 14:53:44.905, PlatformID = 6, DeploymentID = 0x1 2015/10/05 14:53:45.025, Turning ON deployment mode 2015/10/05 14:53:45.081, Turning on modem 2015/10/05 14:54:04.653, Turning off modem 2015/10/05 14:54:04.746, InvenSense MPL v4.0.0 Sep 29 2015 11:08:08 2015/10/05 14:54:04.779, umplInit rtn code = 0 2015/10/05 14:54:05.198, umplStartMPU rtn code = 0 2015/10/05 14:54:05.232, Entering main processing loop 2015/10/05 14:54:05.265, Turning off modem 2015/10/05 14:54:05.299, Entering Watch Cycle 2015/10/05 14:54:05.351, Opening data file 60100001.WAT 2015/10/05 14:54:24.964, Turning on modem 2015/10/05 14:54:51.033, Got modem connection 2015/10/05 14:54:51.145, Exiting Watch Cycle 2015/10/05 14:54:51.178, Running User I/F on console port BEDS)>reset Privilege violation BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>reset This could cause permanent loss of communication. Are you really sure [N] ? user:61> user:61> OK user:62> CONNECT 00800 bits/sec BEDS)> BEDS)> BEDS)> BEDS)>type beds.cfg START 10/4/2015 18:00:00 platformID = 6 ModemAddr = 6 deploymentID = 1 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 600 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>analog Channel 0 = 56720 counts 2.16 volts 26.202 Batt Volts Channel 1 = 56734 counts 2.16 volts 26.209 Batt Volts Channel 2 = 6625 counts 0.25 volts 0.136 bar Channel 3 = 14679 counts 0.56 volts 15.498 psia Channel 4 = 18866 counts 0.72 volts 21.968 degC Channel 5 = 26978 counts 1.03 volts 24.729 % BEDS)>resetr       BEDS)>reset This could cause permanent loss of communication. Are you really sure [N] ? BEDS)> BEDS)>time Accurate time is: Monday October 05, 2015 03:01:44.704 pm Persistor clock is 0.551 seconds behind accurate clock BEDS)>time Accurate time is: Monday October 05, 2015 03:02:28.213 pm Persistor clock is 0.551 seconds behind accurate clock BEDS)>date 10/5/           BEDS)>date @>sv5 oU?2eE N MMwhǐzΫ&M.qL|1 03:03:02.\N\x-,Pers|0Qa oMk is 6r5ase5oniOvBehibd-+urte c?I}( BEDS)> BEDS)> BEDS)>time Accurate time ig DI/Ty ctober 05, 2015 &-4.796 pm ersistor clock is 0.551zscondr behind accurate clock BEDS)> BEDS)>time Accurate time is: Monday October 05, 2015 03:04:10.764 pm Persistor clock is 0.551 seconds behind accurate clock BEDS)>date 10/1/2015 Accurate time is: Monday October 05, 2015 03:04:27.503 pm Persistor clock is 0.551 seconds behind accurate clock BEDS)>quit user:63> OK user:64> Response Not Received user:65> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=007 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=004 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:66> CONNECT 00800 bits/sec user:67> Response Not Received user:68> Invalid Command user:69> Response Not Received user:70> Command '+++' not found Error user:71> OK user:72> CONNECT 00800 bits/sec user:73> Response Not Received user:74> Response Not Received user:75> Response Not Received user:76> Range 0 to 5 : 1.2 m user:77> CONNECT 00800 bits/sec user:78> OK user:79> user:79> CONNECT 00800 bits/sec BEDS)> BEDS)>time Accurate time is: Monday October 05, 2015 03:10:36.549 pm Persistor clock is 0.541 seconds behind accurate clock BEDS)>h ~~~~~~~~~~~~~~~ Benthic Event Detection System ~~~~~~~~~~~~~~~~~~ ~~~ To start recording inertial data, QUIT the command interface ~~~ PRIV Set cmd parser priv level EVENT Get Events WATCH Show watch cycles SYSRECS Get System Records VAR Get/Set variable QUIT Exit command parser SYSLOG Write to system logger DECODE Decode data file ANALOG Read analog chan DECIMATE Decimate and split files SPLIT Split and decimate files MORE Paginate file TAIL TAIL DEPLOY Set/reset/show deployment DATE print date/time DIR [d:][p][fn] [/PWBLV4A:a] TIME [hh:mm:ss [a|p]] [/M/C] TYPE [drv:][pth][name] XS [/X][/C][/Q]file XR [/X][/C][/Q][file] YS [/G][/Q]file[,file...] YR [/G][/Q] ZS ZModem send KS Kermit send VER Firmware versions BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>atime /? Bad command or file name BEDS)>h ~~~~~~~~~~~~~~~ Benthic Event Detection System ~~~~~~~~~~~~~~~~~~ ~~~ To start recording inertial data, QUIT the command interface ~~~ PRIV Set cmd parser priv level EVENT Get Events WATCH Show watch cycles SYSRECS Get System Records VAR Get/Set variable QUIT Exit command parser SYSLOG Write to system logger DECODE Decode data file ANALOG Read analog chan DECIMATE Decimate and split files SPLIT Split and decimate files MORE Paginate file TAIL TAIL DEPLOY Set/reset/show deployment DELETELINE Delete one line from file DELETECHARS Delete chars from file INSERTLINE Insert one line in file INSERTCHARS Insert chars in file RECOVER equiv to RESET PICO MODEM Send commands to modem SETPCLK Set PicoDOS RTC from accurSETACLK Set accurate RTC from Pico APP run flash app [args...] ATTRIB [+ - RASH] [d:][p][name] BACKROM/ [d:][path] [/SAVI] BAUD [newrate] [/Q/P/E/O/N/2] BOOT [PICO][PBM][APP] CAPTURE [d:][p]fn [/Dx/B/N/E] CCC Card Change [delay secs] CHDIR [drive:][path] CHKDSK [d:][p][fn] [/F][/I] COPY source dest [/V] DUMP file[start[,end]] DATE print date/time PDATE [mdy[hms[a|p]]] /IEUMCP] DEL [drv:][pth][name] [/P] DIR [d:][p][fn] [/PWBLV4A:a] ERASE [drv:][pth][name] [/P] FDISK [/Pnn/M/Sdev/@/F/Rnn/Q] FORMAT [drv:][/V[:label]][/Q/E] GO args... | addr /A | /Fn LO [ofs][;Bx[+]] [;G] MKDIR [drive:][path] MD display [range] MM modify [address] ML disassemble [range] MON Reset to PBM PATH [[d:]path[;...]] [/P] PBM Reset to PBM PROMPT [text] [/P] PR pin read <1..50> PC pin clear <1..50> PS pin set <1..50> PT pin toggle <1..50> PM pin mirror <1..50> TIME [hh:mm:ss [a|p]] [/M/C] PTIME [hh:mm:ss [a|p]] [/M/C] TYPE [drv:][pth][name] REN [d:][p]oldname newname RESET (hard reset) RMDIR [drive:][path] SAVE file[start][end] SD sect.dump[d:][range][/C] SET [var=[str]] [/SLFE?] XS [/X][/C][/Q]file XR [/X][/C][/Q][file] YS [/G][/Q]file[,file...] YR [/G][/Q] ZS ZModem send KS Kermit send VER Firmware versions BEDS)>date /? Accurate time is: Monday October 05, 2015 03:12:47.653 pm Persistor clock is 0.541 seconds behind accurate clock BEDS)>time 10/1/2015 15:13:30 5 Accurate time is: Monday October 05, 2015 03:13:40.252 pm Persistor clock is 0.541 seconds behind accurate clock BEDS)>dir Volume in drive C has no label Volume Serial Number is 413C-297A Directory of C:\ BEDS.CFG 245 10-05-15 2:52p MPULOG.001 342 10-05-15 2:57p EVENTIDX.001 18 10-05-15 2:57p WATCHIDX.001 50 10-05-15 2:57p EVENTIDX.002 18 10-05-15 2:53p BEDS.BAK 246 10-05-15 10:45a BEDSCLK.001 8 10-05-15 2:57p WATCHIDX.002 50 10-05-15 2:54p EVENTIDX.003 18 10-05-15 12:29p SYSLOG.001 933 10-05-15 3:00p MPULOG.002 463 10-05-15 2:54p RTC.PXE 28,270 10-01-15 11:52p 60100001.WAT 5,064 10-05-15 3:01p BEDSCLK.002 8 10-05-15 2:54p WATCHIDX.003 50 10-05-15 2:50p EVENTIDX.004 50 10-05-15 10:33a SYSLOG.002 933 10-05-15 2:57p MPULOG.000]| 8,629 10-05-15 2:50p BEDSCLK.003 1,136 10-05-15 2:50p WATCHIDX.004 178 10-05-15 10:44a BEDS.CLK 56 10-05-15 3:10p SYSLOG.003 3,061 10-05-15 2:53p SYSLOG.TXT 1,267 10-05-15 3:11p BEDSCLK.004 24 10-05-15 10:44a EVENT.IDX 18 10-05-15 3:00p WATCH.IDX 82 10-05-15 3:10p SYSLOG.004 58 10-05-15 10:46a MPULOG.TXT 771 10-05-15 3:06p 60100002.WAT 59,310 10-05-15 3:10p 29 file(s) 109 KB 0 dir(s) 31,241,664 KB free BEDS)>pdate 10.1.2015 Clock reads: Thursday, October 01, 2015 03:15:39 pm BEDS)>time 15:15:15 Accurate time is: Thursday October 01, 2015 03:16:18.121 pm Persistor clock is 0.541 seconds behind accurate clock BEDS)>time 15:15:30 Accurate time is: Thursday October 01, 2015 03:16:54.269 pm Persistor clock is 0.541 seconds behind accurate clock BEDS)>time 15:17:30 Accurate time is: Thursday October 01, 2015 03:17:27.258 pm Persistor clock is 0.541 seconds behind accurate clock BEDS)>setaclk Setting accurate RTC from PicoDOS RTC Clock reads: Thursday, October 01, 2015 03:17:40 pm BEDS)>quit user:80> OK user:81> CONNECT 00800 bits/sec BEDS*87|> BEDS)> user:82> OK user:83> CONNECT 00800 bits/sec BEDS)> BEDS)>time Accurate time is: Thursday October 01, 2015 03:20:43.600 pm Persistor clock is 0.289 seconds ahead of accurate clock BEDS)>reset Privilege violation BEDS)> BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>reset This could cause permanent loss of communication. Are you really se [N] ? user:84> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=008 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=006 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:85> CONNECT 00800 bits/sec BEDS)> BEDS)>type beds.cfg START 10/4/2015 18 BEDS)>time Accurate time is: Thursday October 01, 2015 03:23:36.255 pm Persistor clock is 0.819 seconds behind accurate clock BEDS)>reset Privilege violation BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>reset This could cause permanent loss of communication. lre you really se [N] ? BEDS)> BEDS)>time Accurate time is: Thursday October 01, 2015 03:25:27.146 pm Persistor clock is 0.654 seconds behind accurate clock BEDS)>var,deploymodesecs DeployModeSecs = 86400 How long (seconds) to stay in deployment mode BEDS)>deploymodesecs = 345600 DeployModeSecs = 345600 BEDS)> user:86> OK user:87> CONNECT 00800 bits/sec user:88> OK user:89> CONNECT 00800 bits/sec user:90> user:91> Command '+++' not found Error user:92> user:92> OK user:93> CONNECT 00800 bits/sec TIMEOUT BEDS)> BEDS)>analog Channel 0 = 7JA 9ƲN;1 volts 26.737 Batt Volts ChannelC14F^_)LJnnts p2.|#ݶolts 26. ~Άt Volts ChaMYY b 0analog Chaonl 0 = 57289 count+h.19Tvlt2/ -Batt Volts Ccannem 1 57173 counts 2.18 ults 26.412 Batt Volts Chanel 2 = 6975 counts 0.27vTl s 50tar ChaUA>R~595 counts 0.56 volts 15.338 pria Chanm`=N87933co\s 0.72 volts 21.690 degC Channel  26643 counts 1.02 volts 24.26 % BEDS)>analog Channel 0 = 56659 counts 2.16 volts 26.174 Batt Volts Channel 1 = 54634 counts 2.08 volts 25.239 Batt Volts Channel 2 = 6975 counts 0.27 volts 0.804 bar Channel 3 = 14595 counts 0.56 volts 15.338 psia Channel 4 = 18841 counts 0.72 volts 21.873 degC Channel 5 = 26541 counts 1.01 volts 23.943 % BEDS)>time Acculate time is: ThOy Ocober 0,>DŽ4۔9:59.77? pm PerkH[z>!(Z0.800 seconds4{ind aeZUa&lock DS)>ti e Aaurate time is: ThurWVy October 01, Atime Accurate time is: Thursday October 01, 2015 03:30:34.017 pm Persistor clock is 0.800 seconds behind accurate clock BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>deletechar 1 beds.cfg BEDS)>type beds.cfg START 10/4/2015 18:00:00 platformID = 5 ModemAddr = 5 deploymentID = 1 ModemPower = 6 #logToConsole = 3 Timeout = 120 ModemWarmup = 15 ModemOnTime = 60 ModemOffset = 480 SensorWarmup = 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>reset This could cause permanent loss of communication. Are you really sure [N] ? user:94> OK user:95> CONNECT 00800 bits/sec user:96> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=008 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=006 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:97> OK user:98> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=008 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=004 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:99> Range 0 to 3 : 0.0 m user:100> OK user:101> CONNECT 00800 bits/sec BEDS)> BEDS)>type syslog.txt 2015/10/01 14:39:29.573, SysLog started 2015/10/01 14:39:29.727, PlatformID = 3, DeploymentID = 0x2 2015/10/01 14:39:29.025, Turning ON deployment mode 2015/10/01 14:39:29.081, Turning on modem 2015/10/01 14:39:48.734, Turning off modem 2015/10/01 14:39:48.767, Turning off modem 2015/10/01 14:39:48.828, Sleeping until Sun Oct 4 18:00:00 2015 2015/10/01 14:39:48.968, Woke due to keyboard char 2015/10/01 14:39:49.061, InvenSense MPL v4.0.0 Sep 29 2015 11:08:08 2015/10/01 14:39:49.094, umplInit rtn code = 0 2015/10/01 14:39:49.520, umplStartMPU rtn code = 0 2015/10/01 14:39:49.555, Entering main processing loop 2015/10/01 14:39:49.588, Turning off modem 2015/10/01 14:39:49.623, Entering Watch Cycle 2015/10/01 14:39:49.669, Opening data file 30200001.WAT 2015/10/01 14:39:50.923, Turning on modem 2015/10/01 14:41:04.042, Timed out waiting for modem connection 2015/10/01 14:41:04.077, Turning off modem 2015/10/01 14:44:00.070, Turning on modem 2015/10/01 14:45:14.035, Timed out waiting for modem connection 2015/10/01 14:45:14.071, Turning off modem 2015/10/01 14:54:00.062, Turning on modem 2015/10/01 14:55:14.040, Timed out waiting for modem connection 2015/10/01 14:55:14.073, Turning off modem 2015/10/01 15:04:00.063, Turning on modem 2015/10/01 15:05:14.037, Timed out waiting for modem connection 2015/10/01 15:05:14.070, Turning off modem 2015/10/01 15:14:00.075, Turning on modem 2015/10/01 15:15:14.039, Timed out waiting for modem connection 2015/10/01 15:15:14.072, Turning off modem 2015/10/01 15:24:00.062, Turning on modem 2015/10/01 15:25:14.040, Timed out waiting for modem connection 2015/10/01 15:25:14.073, Turning off modem 2015/10/01 15:34:00.068, Turning on modem 2015/10/01 15:34:40.041, Got modem connection 2015/10/01 15:34:40.139, Exiting Watch Cycle 2015/10/01 15:34:40.172, Running User I/F on console port BEDS)> BEDS)>priv 100 Setting command parser privilege to 100 BEDS)>reset This could cause permanent loss of communication. Are you really sure [N] ? y user:102> user:103> OK user:104> CONNECT 00800 bits/sec BEDS)> BEDS)>deploymodesecs = 345600 DeployModeSecs = 345600 BEDS)>deploy Deployment mode = ON BEDS)>quit user:105> OK user:106> Local Sregisters S00=086 S01=000 S02=000 S03=002 S04=005 S05=000 S06=008 S07=015 S08=060 S09=001 S10=255 S11=000 S12=000 S13=001 S14=004 S15=001 S16=001 S17=001 S18=000 S19=000 S20=000 user:107> CONNECT 00800 bits/sec BEDS)> BEDS)> TIMEOUT user:108> Response Not Received user:109> Command 'r4' not found Error user:110> Response Not Received user:111> Command '++++++' not found Error user:112> CONNECT 00800 bits/sec BEDS)> BEDS)>type beds.cfg #START 10/4/2015 18:00:00 platformID = 4 Mod`mAddr = 4 deploymentID = 1 ModemPower = 6 #logToConsole = 3 Timeout = 120 Modmpakup = 15 ModemOnTime = 60 ModemOffset = 360 SensorWarl*= 5 SensorMinSecs = 10 NoMotionThresh = 12.0 BEDS)>analog Channel 0 = 58524 counts 2.23 volts 27.036 Batt Volts Channel 1 = 58493 counts 2.23 volts 27.021 Batt Volts Channel 2 = 6435 counts 0.25 volts -0.226 bar Channel 3 = 15079 counts 0.58 volts 16.261 psia Channel 4 = 25820 counts 0.98 volts 48.495 degC Channel 5 = 19215 counts 0.73 volts 10.759 % BEDS)> BEDS)>analog Channel 0 = 58284 counts 2.22 volts 26.925 Batt Volts Channel 1 = 58252 counts 2.22 volts 26.910 Batt Volts Channel 2 = 6429 counts 0.25 volts -0.238 bar Channel 3 = 15063 counts 0.57 volts 16.230 psia Channel 4 = 25896 counts 0.99 volts 48.785 degC Channel 5 = 19163 counts 0.73 volts 10.665 % BEDS)>eploymodesecs = 465600 DeployModeSecs = 465600 BEDS)>deploymodesecs = 345600 DeployModeSecs = 345600 BEDS)>deploy Deployment mode = ON BEDS)>analog Channel 0 = 58219 counts 2.22 volts 26.895Batt Volts Channel 1 = 58188 counts 2.22 volts 26.881 Batt Wolts Channel 2 > 6431 counts 0.25 volts -0.234 bar Channel 3 = 15078 counts 0.58 volts 16.259 psiajChannel != 25992 counts 0.99 volts 49.152 degC Channel 5 = 9110 counts 0.73 volts 10.570 % BEDS)>analog Channel 0 = 58024 counts 2.21 volts 26.805 Batt Volts Channel 1 = 57991 counts 2.21 volts 26.790 Batt Volts Channel 2 = 6429 counts 0.25 volts -0.238 bar Channel 3 = 1 ] counts 0.58 volts 16.259 psia Channel 4 = 25999 counts 0.99 volts 49.178 degC Channel 5 = 19111 counts 0.73 volts 10.572 % BEDS)> TIMEOUT BEDS)>c analog Channel 0 = 59330 counts 2.26 volts 27.408 Batt Volts Channel 1 = 59599 counts 2.27 volts 27.532 Batt Volts Channel 2 = 6466 counts 0.25 volts -0.167 bar Channel 3 = 14375 counts 0.55 volts 14.918 psia Channel 4 = 24708 counts 0.94 volts 44.254 degC Channel 5 = 23431 counts 0.89 volts 18.346 % BEDS)>reset /p This could cause permanent loss of communication. Are you really sure [N] ? y Dismounting C: Ok (0)