Lantronix Web Based Configuration Manager
Software Release Notes  
Version 1.8.0.1
April 22, 2010
Copyright 2004-2010, Lantronix


The Web Configuration Manager 1.8.0.1 is an updated release for the web 
based configuration tool for the Device Server Products.

It supports the products running the following firmware:

6.7.0.1 - MatchPort NR
6.7.0.1 - XPort 03/04

===============
RELEASE SUMMARY
===============
Current release: 1.8.0.1


============================
SYSTEM REQUIREMENTS
============================

Microsoft Windows XP (SP1), 2000, NT 4.0, 98 (1st and 2nd edition).
Pentium 166 Mhz or faster
64 MB of physical RAM.

Javascript must be enabled.

Browsers Supported:
  -> Internet Explorer 7.0
  -> Internet Explorer 6.0
  -> Firefox 2.0.0.2


=================
SOFTWARE RELEASES
=================

mptNR_webm_1801.cob    - MatchPort NR WebManager
xpt_webm_1801.cob      - XPort 03/04 Web Manager


============
NEW FEATURES
============
Configuration for Minimum Data Transmission Rate and Max Packet
Transmission Failures (MaxTxFail) has been added to the WiFi 
Settings Page.




From 1.7.0.1 Release
--------------------
The Web Manager enables configuration of all options available for the
Lantronix Device server products running firmware version 6.6.0.X

From 1.7.0.0 Release
--------------------
-> Addition of Soft AP Roaming Feature

-> Addition of DNS Server Feature


From 1.6.0.2 Release
--------------------

-> Feature request C-050803-68489 the ability to turn off the display of the
   remote ip address in modem mode

-> Feature request C-051020-71865 The ability to use a broadcast address with
   UDP

-> Feature request C-041022-55131 The ability to have the XPort Link Status
   reported on an IO pin 


From 1.5.0.2 Release
--------------------
-> Telnet mode has been changed to Com Port Control Mode to support RFC2217


From 1.5.0.0 Release
--------------------

-> Configuration for Bridging Mode has been added in the Network Settings Page
   This also allows configuration of the Wired Only, Wireless Only modes in
   addition to the Bridging (Single Host) Mode. The Network interface settings from
   the WLAN page has not been rolled into this mode.

-> Addition of configurable 0x77fe (LCAP) port number when bridging is enabled.

-> Support for 802.11i/WPA2 Security Method has been added via a new Security
   Method tab within WLAN Settings Page. Supports Pre-Shared Keys

-> Addition of Spain and Canada in the list of countries and their corresponding
   channel boundaries.

-> Addition of "Reset to Defaults (Ethernet)" function to the configurable pins
   When used, this would allow the firmware to reset the settings to factory
   defaults including the network settings and select the Wired Only network mode
   for operation on restart.


=========
BUG FIXES
=========

Bugzilla 10009 - Remote address field is greyed out when use broadcast option is unchecked.
Bugzilla 10010 - Garbage characters seen in remote host field when use broadcast option is checked.
Bugzilla 10013 - Device enters monitor mode with hostlist configuration
Bugzilla 10018 - Clarify that telnet password is used for both Web Manager and Telnet setup menu access
Bugzilla 10019 - Telnet session does not show subsequent hostlist info when first host is modified
Bugzilla 10029, 10030, 10066, 10112, 10116, 10139 - Incorrect parsing of decimal values with leading zeros

From 1.8.0.0 Release
---------------------
Bugzilla 9447 (WiPort NR) Invalid option in 'Configurable Pins' page


From 1.7.0.1 Release
--------------------
C-071108-101540 - "Accept Incoming" config on UDP web page has no effect


From 1.7.0.0 Release
--------------------
C-071219-102965 - Webmanager problem with dns field when using DHCP


From 1.6.0.4 Release
--------------------
C-070827-98596 - Webmanager can not disable TCP Keepalive using "0"


From 1.6.0.2 Release
--------------------
C-070112-89495 - XPort CP's Misleading in Web Manager Interface
5702           - Mac Address and Firmware version do not display in IE 7
C-070221-90987 - Mac Address and Firmware version do not display in IE 7
C-060327-78243 - RS485 Option in port settings
C-060303-77318 - WPA passphrase Characters will now accept all printable ASCII
                 characters
C-060321-77977 - XPort CP 485 Active Level
C-061019-86509 - Web manager will not allow "0.0.0.0" for remote UDP address


From 1.5.0.3 Release
--------------------
C-060327-78243 - WiBox - Web/Menu Allow Port 1 To Config RS485 2/4 Wire Only
                 Port 2 Supports 
C-060906-84695 - WiBox - Web 1.5.x Cannot Config Trailing Chars If Send
                 Frame Checked
C-060920-85282 - WiBox - Web 1.5.0.1RC2 Hostlist Retrytimeout Allows Invalid
                 Values of 1-9


From 1.5.0.0 Release
--------------------
C-060117-75298 - WiBox - Web will not allow 32 Hex Values
C-060227-76997 - CPU Performance mode bug fixed, with selection of higher
               baudrates.
C-060227-77005 - Xport - UDP Datagram Type 01 and Buffer Flushing should not be
               enabled simultaneously.
C-060327-78240 - Xport - WebM will now allow Remote Port 0 in UDP mode
C-060327-78242 - WiBox Web Manager Will Not Allow Key Entry For WPA +WEP128
C-060410-78820 - WiBox WebM allows Blank WEP Key When Enabling WEP
C-060426-79476 - WiBox FireFox Allows Setting "Device Address Table" in UDP mode.
C-060517-80300 - XPort Web manager will not set "Check EOT"

-> When in Adhoc mode, the WLAN settings page onLoad issues a Javascript error.
-> Security Method does not display the correct WPA or WPA2/802.11i mode on page
   load.


============
KNOWN ISSUES
============