// diskio.c
// Renamed from mmc-dk-tm4c123g.c to avoid confusion (RCG 4/14)

/*-----------------------------------------------------------------------*/
/* MMC/SDC (in SPI mode) control module  (C)ChaN, 2007                   */
/*-----------------------------------------------------------------------*/
/* Only rcvr_spi(), xmit_spi(), disk_timerproc() and some macros         */
/* are platform dependent.                                               */
/*-----------------------------------------------------------------------*/

/*
 * This file was modified from a sample available from the FatFs
 * web site. It was modified to work with an DK-TM4C123G development
 * board.
 */

#include "system.h"
#include "fatfs/src/diskio.h"

/* Definitions for MMC/SDC command */
#define CMD0    (0x40+0)    /* GO_IDLE_STATE */
#define CMD1    (0x40+1)    /* SEND_OP_COND */
#define CMD8    (0x40+8)    /* SEND_IF_COND */
#define CMD9    (0x40+9)    /* SEND_CSD */
#define CMD10    (0x40+10)    /* SEND_CID */
#define CMD12    (0x40+12)    /* STOP_TRANSMISSION */
#define CMD16    (0x40+16)    /* SET_BLOCKLEN */
#define CMD17    (0x40+17)    /* READ_SINGLE_BLOCK */
#define CMD18    (0x40+18)    /* READ_MULTIPLE_BLOCK */
#define CMD23    (0x40+23)    /* SET_BLOCK_COUNT */
#define CMD24    (0x40+24)    /* WRITE_BLOCK */
#define CMD25    (0x40+25)    /* WRITE_MULTIPLE_BLOCK */
#define CMD41    (0x40+41)    /* SEND_OP_COND (ACMD) */
#define CMD55    (0x40+55)    /* APP_CMD */
#define CMD58    (0x40+58)    /* READ_OCR */

/* Peripheral definitions for DK-TM4C123G board */
// SSI port
#define SDC_SSI_BASE            SSI0_BASE
#define SDC_SSI_SYSCTL_PERIPH   SYSCTL_PERIPH_SSI0

// GPIO for SSI pins
#define SDC_GPIO_PORT_BASE      GPIO_PORTA_BASE
#define SDC_GPIO_SYSCTL_PERIPH  SYSCTL_PERIPH_GPIOA
#define SDC_SSI_CLK             GPIO_PIN_2
#define SDC_SSI_TX              GPIO_PIN_5
#define SDC_SSI_RX              GPIO_PIN_4
#define SDC_SSI_FSS             GPIO_PIN_3
#define SDC_SSI_PINS            (SDC_SSI_TX | SDC_SSI_RX | SDC_SSI_CLK |      \
                                 SDC_SSI_FSS)

// asserts the CS pin to the card
static
void SELECT (void)
{
    ROM_GPIOPinWrite(SDC_GPIO_PORT_BASE, SDC_SSI_FSS, 0);
}

// de-asserts the CS pin to the card
static
void DESELECT (void)
{
    ROM_GPIOPinWrite(SDC_GPIO_PORT_BASE, SDC_SSI_FSS, SDC_SSI_FSS);
}

/*--------------------------------------------------------------------------

   Module Private Functions

---------------------------------------------------------------------------*/

static volatile
DSTATUS Stat = STA_NOINIT;    /* Disk status */

static volatile
BYTE Timer1, Timer2;    /* 100Hz decrement timer */

static
BYTE CardType;            /* b0:MMC, b1:SDC, b2:Block addressing */

static
BYTE PowerFlag = 0;     /* indicates if "power" is on */

/*-----------------------------------------------------------------------*/
/* Transmit a byte to MMC via SPI  (Platform dependent)                  */
/*-----------------------------------------------------------------------*/

static
void xmit_spi(BYTE dat)
{
    uint32_t ui32RcvDat;

    ROM_SSIDataPut(SDC_SSI_BASE, dat); /* Write the data to the tx fifo */

    ROM_SSIDataGet(SDC_SSI_BASE, &ui32RcvDat); /* flush data read during the write */
}


/*-----------------------------------------------------------------------*/
/* Receive a byte from MMC via SPI  (Platform dependent)                 */
/*-----------------------------------------------------------------------*/

static
BYTE rcvr_spi (void)
{
    uint32_t ui32RcvDat;

    ROM_SSIDataPut(SDC_SSI_BASE, 0xFF); /* write dummy data */

    ROM_SSIDataGet(SDC_SSI_BASE, &ui32RcvDat); /* read data frm rx fifo */

    return (BYTE)ui32RcvDat;
}


static
void rcvr_spi_m (BYTE *dst)
{
    *dst = rcvr_spi();
}

/*-----------------------------------------------------------------------*/
/* Wait for card ready                                                   */
/*-----------------------------------------------------------------------*/

static
BYTE wait_ready (void)
{
    BYTE res;


    Timer2 = 50;    /* Wait for ready in timeout of 500ms */
    rcvr_spi();
    do
        res = rcvr_spi();
    while ((res != 0xFF) && Timer2);

    return res;
}

/*-----------------------------------------------------------------------*/
/* Send 80 or so clock transitions with CS and DI held high. This is     */
/* required after card power up to get it into SPI mode                  */
/*-----------------------------------------------------------------------*/
static
void send_initial_clock_train(void)
{
    unsigned int i;
    uint32_t ui32Dat;

    /* Ensure CS is held high. */
    DESELECT();

    /* Switch the SSI TX line to a GPIO and drive it high too. */
    ROM_GPIOPinTypeGPIOOutput(SDC_GPIO_PORT_BASE, SDC_SSI_TX);
    ROM_GPIOPinWrite(SDC_GPIO_PORT_BASE, SDC_SSI_TX, SDC_SSI_TX);

    /* Send 10 bytes over the SSI. This causes the clock to wiggle the */
    /* required number of times. */
    for(i = 0 ; i < 10 ; i++)
    {
        /* Write DUMMY data. SSIDataPut() waits until there is room in the */
        /* FIFO. */
        ROM_SSIDataPut(SDC_SSI_BASE, 0xFF);

        /* Flush data read during data write. */
        ROM_SSIDataGet(SDC_SSI_BASE, &ui32Dat);
    }

    /* Revert to hardware control of the SSI TX line. */
    ROM_GPIOPinTypeSSI(SDC_GPIO_PORT_BASE, SDC_SSI_TX);
}

/*-----------------------------------------------------------------------*/
/* Power Control  (Platform dependent)                                   */
/*-----------------------------------------------------------------------*/
/* When the target system does not support socket power control, there   */
/* is nothing to do in these functions and chk_power always returns 1.   */

static
void power_on (void)
{
    /*
     * This doesn't really turn the power on, but initializes the
     * SSI port and pins needed to talk to the card.
     */

    /* Enable the peripherals used to drive the SDC on SSI */
    ROM_SysCtlPeripheralEnable(SDC_SSI_SYSCTL_PERIPH);
    ROM_SysCtlPeripheralEnable(SDC_GPIO_SYSCTL_PERIPH);

    /*
     * Configure the appropriate pins to be SSI instead of GPIO. The FSS (CS)
     * signal is directly driven to ensure that we can hold it low through a
     * complete transaction with the SD card.
     */
    ROM_GPIOPinTypeSSI(SDC_GPIO_PORT_BASE, SDC_SSI_TX | SDC_SSI_RX | SDC_SSI_CLK);
    ROM_GPIOPinTypeGPIOOutput(SDC_GPIO_PORT_BASE, SDC_SSI_FSS);

    /*
     * Set the SSI output pins to 4MA drive strength and engage the
     * pull-up on the receive line.
     */
    ROM_GPIOPadConfigSet(SDC_GPIO_PORT_BASE, SDC_SSI_RX, GPIO_STRENGTH_4MA,
                         GPIO_PIN_TYPE_STD_WPU);
    ROM_GPIOPadConfigSet(SDC_GPIO_PORT_BASE, SDC_SSI_CLK | SDC_SSI_TX | SDC_SSI_FSS,
                         GPIO_STRENGTH_4MA, GPIO_PIN_TYPE_STD);

    /* Configure the SSI0 port */
    ROM_SSIConfigSetExpClk(SDC_SSI_BASE, ROM_SysCtlClockGet(),
                           SSI_FRF_MOTO_MODE_0, SSI_MODE_MASTER, 400000, 8);
    ROM_SSIEnable(SDC_SSI_BASE);

    /* Set DI and CS high and apply more than 74 pulses to SCLK for the card */
    /* to be able to accept a native command. */
    send_initial_clock_train();

    PowerFlag = 1;
}

// set the SSI speed to the max setting
static
void set_max_speed(void)
{
    unsigned long i;

    /* Disable the SSI */
    ROM_SSIDisable(SDC_SSI_BASE);

    /* Set the maximum speed as half the system clock, with a max of 12.5 MHz. */
    i = ROM_SysCtlClockGet() / 2;
    if(i > 12500000)
    {
        i = 12500000;
    }

    /* Configure the SSI0 port to run at 12.5MHz */
    ROM_SSIConfigSetExpClk(SDC_SSI_BASE, ROM_SysCtlClockGet(),
                           SSI_FRF_MOTO_MODE_0, SSI_MODE_MASTER, i, 8);

    /* Enable the SSI */
    ROM_SSIEnable(SDC_SSI_BASE);
}

static
void power_off (void)
{
    PowerFlag = 0;
}

static
int chk_power(void)        /* Socket power state: 0=off, 1=on */
{
    return PowerFlag;
}



/*-----------------------------------------------------------------------*/
/* Receive a data packet from MMC                                        */
/*-----------------------------------------------------------------------*/

static
BOOL rcvr_datablock (
    BYTE *buff,            /* Data buffer to store received data */
    UINT btr            /* Byte count (must be even number) */
)
{
    BYTE token;


    Timer1 = 100;
    do {                            /* Wait for data packet in timeout of 100ms */
        token = rcvr_spi();
    } while ((token == 0xFF) && Timer1);
    if(token != 0xFE) return FALSE;    /* If not valid data token, retutn with error */

    do {                            /* Receive the data block into buffer */
        rcvr_spi_m(buff++);
        rcvr_spi_m(buff++);
    } while (btr -= 2);
    rcvr_spi();                        /* Discard CRC */
    rcvr_spi();

    return TRUE;                    /* Return with success */
}



/*-----------------------------------------------------------------------*/
/* Send a data packet to MMC                                             */
/*-----------------------------------------------------------------------*/

#if _READONLY == 0
static
BOOL xmit_datablock (
    const BYTE *buff,    /* 512 byte data block to be transmitted */
    BYTE token            /* Data/Stop token */
)
{
    BYTE resp, wc;


    if (wait_ready() != 0xFF) return FALSE;

    xmit_spi(token);                    /* Xmit data token */
    if (token != 0xFD) {    /* Is data token */
        wc = 0;
        do {                            /* Xmit the 512 byte data block to MMC */
            xmit_spi(*buff++);
            xmit_spi(*buff++);
        } while (--wc);
        xmit_spi(0xFF);                    /* CRC (Dummy) */
        xmit_spi(0xFF);
        resp = rcvr_spi();                /* Reveive data response */
        if ((resp & 0x1F) != 0x05)        /* If not accepted, return with error */
            return FALSE;
    }

    return TRUE;
}
#endif /* _READONLY */



/*-----------------------------------------------------------------------*/
/* Send a command packet to MMC                                          */
/*-----------------------------------------------------------------------*/

static
BYTE send_cmd (
    BYTE cmd,        /* Command byte */
    DWORD arg        /* Argument */
)
{
    BYTE n, res;


    if (wait_ready() != 0xFF) return 0xFF;

    /* Send command packet */
    xmit_spi(cmd);                        /* Command */
    xmit_spi((BYTE)(arg >> 24));        /* Argument[31..24] */
    xmit_spi((BYTE)(arg >> 16));        /* Argument[23..16] */
    xmit_spi((BYTE)(arg >> 8));            /* Argument[15..8] */
    xmit_spi((BYTE)arg);                /* Argument[7..0] */
    n = 0xff;
    if (cmd == CMD0) n = 0x95;            /* CRC for CMD0(0) */
    if (cmd == CMD8) n = 0x87;            /* CRC for CMD8(0x1AA) */
    xmit_spi(n);

    /* Receive command response */
    if (cmd == CMD12) rcvr_spi();        /* Skip a stuff byte when stop reading */
    n = 10;                                /* Wait for a valid response in timeout of 10 attempts */
    do
        res = rcvr_spi();
    while ((res & 0x80) && --n);

    return res;            /* Return with the response value */
}

/*-----------------------------------------------------------------------*
 * Send the special command used to terminate a multi-sector read.
 *
 * This is the only command which can be sent while the SDCard is sending
 * data. The SDCard spec indicates that the data transfer will stop 2 bytes
 * after the 6 byte CMD12 command is sent and that the card will then send
 * 0xFF for between 2 and 6 more bytes before the R1 response byte.  This
 * response will be followed by another 0xFF byte.  In testing, however, it
 * seems that some cards don't send the 2 to 6 0xFF bytes between the end of
 * data transmission and the response code.  This function, therefore, merely
 * reads 10 bytes and, if the last one read is 0xFF, returns the value of the
 * latest non-0xFF byte as the response code.
 *
 *-----------------------------------------------------------------------*/

static
BYTE send_cmd12 (void)
{
    BYTE n, res, val;

    /* For CMD12, we don't wait for the card to be idle before we send
     * the new command.
     */

    /* Send command packet - the argument for CMD12 is ignored. */
    xmit_spi(CMD12);
    xmit_spi(0);
    xmit_spi(0);
    xmit_spi(0);
    xmit_spi(0);
    xmit_spi(0);

    /* Read up to 10 bytes from the card, remembering the value read if it's
       not 0xFF */
    for(n = 0; n < 10; n++)
    {
        val = rcvr_spi();
        if(val != 0xFF)
        {
            res = val;
        }
    }

    return res;            /* Return with the response value */
}

/*--------------------------------------------------------------------------

   Public Functions

---------------------------------------------------------------------------*/


/*-----------------------------------------------------------------------*/
/* Initialize Disk Drive                                                 */
/*-----------------------------------------------------------------------*/

DSTATUS disk_initialize (
    BYTE drv        /* Physical drive number (0) */
)
{
    BYTE n, ty, ocr[4];


    if (drv) return STA_NOINIT;            /* Supports only single drive */
    if (Stat & STA_NODISK) return Stat;    /* No card in the socket */

    power_on();                            /* Force socket power on */
    send_initial_clock_train();            /* Ensure the card is in SPI mode */   // DEATHLINE

//FRACK!!!!!!!!!!!!!!!!!!
    // SPI Serial Flash is blocked - cannot get past line 430 - ghost breakpoint or delayed action causing
    // JTAG catastrophic failure.
    //CORTEX_M4_0: GEL Output:
    //Memory Map Initialization Complete
    //CORTEX_M4_0: Can't Run Target CPU: Timed out while waiting for target powerup/polling a hardware resource.
    //FIX - power down the target hardware, exit ccs, power down laptop, wait several minutes,
    // power up laptop, start ccs, power up target hardware.   Hidden breakpoint is gone.
    // Suspect that power cycling the target is all that is required - this target has bias battery and main supply,
    // both should be powered off.


    SELECT();                /* CS = L */
    ty = 0;
    if (send_cmd(CMD0, 0) == 1) {            /* Enter Idle state */
        Timer1 = 100;                        /* Initialization timeout of 1000 msec */
        if (send_cmd(CMD8, 0x1AA) == 1) {    /* SDC Ver2+ */
            for (n = 0; n < 4; n++) ocr[n] = rcvr_spi();
            if (ocr[2] == 0x01 && ocr[3] == 0xAA) {    /* The card can work at vdd range of 2.7-3.6V */
                do {
                    if (send_cmd(CMD55, 0) <= 1 && send_cmd(CMD41, 1UL << 30) == 0)    break;    /* ACMD41 with HCS bit */
                } while (Timer1);
                if (Timer1 && send_cmd(CMD58, 0) == 0) {    /* Check CCS bit */
                    for (n = 0; n < 4; n++) ocr[n] = rcvr_spi();
                    ty = (ocr[0] & 0x40) ? 6 : 2;
                }
            }
        } else {                            /* SDC Ver1 or MMC */
            ty = (send_cmd(CMD55, 0) <= 1 && send_cmd(CMD41, 0) <= 1) ? 2 : 1;    /* SDC : MMC */
            do {
                if (ty == 2) {
                    if (send_cmd(CMD55, 0) <= 1 && send_cmd(CMD41, 0) == 0) break;    /* ACMD41 */
                } else {
                    if (send_cmd(CMD1, 0) == 0) break;                                /* CMD1 */
                }
            } while (Timer1);
            if (!Timer1 || send_cmd(CMD16, 512) != 0)    /* Select R/W block length */
                ty = 0;
        }
    }
    CardType = ty;
    DESELECT();            /* CS = H */
    rcvr_spi();            /* Idle (Release DO) */

    if (ty) {            /* Initialization succeded */
        Stat &= ~STA_NOINIT;        /* Clear STA_NOINIT */
        set_max_speed();
    } else {            /* Initialization failed */
        power_off();
    }

    return Stat;
}



/*-----------------------------------------------------------------------*/
/* Get Disk Status                                                       */
/*-----------------------------------------------------------------------*/

DSTATUS disk_status (
    BYTE drv        /* Physical drive nmuber (0) */
)
{
    if (drv) return STA_NOINIT;        /* Supports only single drive */
    return Stat;
}



/*-----------------------------------------------------------------------*/
/* Read Sector(s)                                                        */
/*-----------------------------------------------------------------------*/

DRESULT disk_read (
    BYTE drv,            /* Physical drive nmuber (0) */
    BYTE *buff,            /* Pointer to the data buffer to store read data */
    DWORD sector,        /* Start sector number (LBA) */
    UINT count            /* Sector count (1..255) */
)
{
    if (drv || !count) return RES_PARERR;
    if (Stat & STA_NOINIT) return RES_NOTRDY;

    if (!(CardType & 4)) sector *= 512;    /* Convert to byte address if needed */

    SELECT();            /* CS = L */

    if (count == 1) {    /* Single block read */
        if ((send_cmd(CMD17, sector) == 0)    /* READ_SINGLE_BLOCK */
            && rcvr_datablock(buff, 512))
            count = 0;
    }
    else {                /* Multiple block read */
        if (send_cmd(CMD18, sector) == 0) {    /* READ_MULTIPLE_BLOCK */
            do {
                if (!rcvr_datablock(buff, 512)) break;
                buff += 512;
            } while (--count);
            send_cmd12();                /* STOP_TRANSMISSION */
        }
    }

    DESELECT();            /* CS = H */
    rcvr_spi();            /* Idle (Release DO) */

    return count ? RES_ERROR : RES_OK;
}



/*-----------------------------------------------------------------------*/
/* Write Sector(s)                                                       */
/*-----------------------------------------------------------------------*/

#if _READONLY == 0
DRESULT disk_write (
    BYTE drv,            /* Physical drive nmuber (0) */
    const BYTE *buff,    /* Pointer to the data to be written */
    DWORD sector,        /* Start sector number (LBA) */
    UINT count            /* Sector count (1..255) */
)
{
    if (drv || !count) return RES_PARERR;
    if (Stat & STA_NOINIT) return RES_NOTRDY;
    if (Stat & STA_PROTECT) return RES_WRPRT;

    if (!(CardType & 4)) sector *= 512;    /* Convert to byte address if needed */

    SELECT();            /* CS = L */

    if (count == 1) {    /* Single block write */
        if ((send_cmd(CMD24, sector) == 0)    /* WRITE_BLOCK */
            && xmit_datablock(buff, 0xFE))
            count = 0;
    }
    else {                /* Multiple block write */
        if (CardType & 2) {
            send_cmd(CMD55, 0); send_cmd(CMD23, count);    /* ACMD23 */
        }
        if (send_cmd(CMD25, sector) == 0) {    /* WRITE_MULTIPLE_BLOCK */
            do {
                if (!xmit_datablock(buff, 0xFC)) break;
                buff += 512;
            } while (--count);
            if (!xmit_datablock(0, 0xFD))    /* STOP_TRAN token */
                count = 1;
        }
    }

    DESELECT();            /* CS = H */
    rcvr_spi();            /* Idle (Release DO) */

    return count ? RES_ERROR : RES_OK;
}
#endif /* _READONLY */



/*-----------------------------------------------------------------------*/
/* Miscellaneous Functions                                               */
/*-----------------------------------------------------------------------*/

DRESULT disk_ioctl (
    BYTE drv,        /* Physical drive nmuber (0) */
    BYTE ctrl,        /* Control code */
    void *buff        /* Buffer to send/receive control data */
)
{
    DRESULT res;
    BYTE n, csd[16], *ptr = buff;
    WORD csize;


    if (drv) return RES_PARERR;

    res = RES_ERROR;

    if (ctrl == CTRL_POWER) {
        switch (*ptr) {
        case 0:        /* Sub control code == 0 (POWER_OFF) */
            if (chk_power())
                power_off();        /* Power off */
            res = RES_OK;
            break;
        case 1:        /* Sub control code == 1 (POWER_ON) */
            power_on();                /* Power on */
            res = RES_OK;
            break;
        case 2:        /* Sub control code == 2 (POWER_GET) */
            *(ptr+1) = (BYTE)chk_power();
            res = RES_OK;
            break;
        default :
            res = RES_PARERR;
        }
    }
    else {
        if (Stat & STA_NOINIT) return RES_NOTRDY;

        SELECT();        /* CS = L */

        switch (ctrl) {
        case GET_SECTOR_COUNT :    /* Get number of sectors on the disk (DWORD) */
            if ((send_cmd(CMD9, 0) == 0) && rcvr_datablock(csd, 16)) {
                if ((csd[0] >> 6) == 1) {    /* SDC ver 2.00 */
                    csize = csd[9] + ((WORD)csd[8] << 8) + 1;
                    *(DWORD*)buff = (DWORD)csize << 10;
                } else {                    /* MMC or SDC ver 1.XX */
                    n = (csd[5] & 15) + ((csd[10] & 128) >> 7) + ((csd[9] & 3) << 1) + 2;
                    csize = (csd[8] >> 6) + ((WORD)csd[7] << 2) + ((WORD)(csd[6] & 3) << 10) + 1;
                    *(DWORD*)buff = (DWORD)csize << (n - 9);
                }
                res = RES_OK;
            }
            break;

        case GET_SECTOR_SIZE :    /* Get sectors on the disk (WORD) */
            *(WORD*)buff = 512;
            res = RES_OK;
            break;

        case CTRL_SYNC :    /* Make sure that data has been written */
            if (wait_ready() == 0xFF)
                res = RES_OK;
            break;

        case MMC_GET_CSD :    /* Receive CSD as a data block (16 bytes) */
            if (send_cmd(CMD9, 0) == 0        /* READ_CSD */
                && rcvr_datablock(ptr, 16))
                res = RES_OK;
            break;

        case MMC_GET_CID :    /* Receive CID as a data block (16 bytes) */
            if (send_cmd(CMD10, 0) == 0        /* READ_CID */
                && rcvr_datablock(ptr, 16))
                res = RES_OK;
            break;

        case MMC_GET_OCR :    /* Receive OCR as an R3 resp (4 bytes) */
            if (send_cmd(CMD58, 0) == 0) {    /* READ_OCR */
                for (n = 0; n < 4; n++)
                    *ptr++ = rcvr_spi();
                res = RES_OK;
            }

//        case MMC_GET_TYPE :    /* Get card type flags (1 byte) */
//            *ptr = CardType;
//            res = RES_OK;
//            break;

        default:
            res = RES_PARERR;
        }

        DESELECT();            /* CS = H */
        rcvr_spi();            /* Idle (Release DO) */
    }

    return res;
}



/*-----------------------------------------------------------------------*/
/* Device Timer Interrupt Procedure  (Platform dependent)                */
/*-----------------------------------------------------------------------*/
/* This function must be called in period of 10ms                        */

void disk_timerproc (void)
{
//    BYTE n, s;
    BYTE n;


    n = Timer1;                        /* 100Hz decrement timer */
    if (n) Timer1 = --n;
    n = Timer2;
    if (n) Timer2 = --n;

}


/*********************************************************************
 * Function:  		DWORD get_fattime(void)
 *
 * Time stamp info for FATFs. Bit field is as follows:
 * 31:25 Years since 1980
 * 24:21 Month 1-12
 * 20-16 Day of month 1-31
 * 15-11 Hours 0-23
 * 10-5  Minutes 0-59
 * 4-0   Seconds/2 0-29
 ********************************************************************/
DWORD get_fattime(void)
{
	time_t cal_time, fatfs_time;
	struct tm *time_info;

	cal_time = ROM_HibernateRTCGet();
	time_info = gmtime(&cal_time);

	fatfs_time = (time_info->tm_year - 80 << 25);		// Years since 1980. Unix tm struct is years since 1900.
	fatfs_time |= ((time_info->tm_mon+1) << 21);		// Correct for Unix month range of 0-11
	fatfs_time |= (time_info->tm_mday << 16);
	fatfs_time |= (time_info->tm_hour << 11);
	fatfs_time |= (time_info->tm_min << 5);
	fatfs_time |= (time_info->tm_sec/2);

	return fatfs_time;
}