/*!
LTC2412: 2-Channel Differential Input 24-Bit No Latency Delta Sigma ADC
LTC2413: 24-Bit No Latency Delta Sigma ADC with Simultaneous 50Hz/60Hz Rejection ADC

@verbatim

The LTC2412 is a 2-channel differential input micropower 24-bit No Latency
Delta-Sigma analog-to-digital converter with an integrated oscillator. It
provides 2ppm INL and 0.16ppm RMS noise over the entire supply range. The two
differential channels are converted alternately with channel ID included in
the conversion results.

The converter accepts any external differential reference voltage from 0.1V to
VCC for flexible ratiometric and remote sensingmeasurement configurations. The
full-scale differential input range is from –0.5VREF to 0.5VREF. The LTC2412
communicates through a flexible 3-wire digital interface which is compatible
with SPI and MICROWIRE protocols.

@endverbatim

http://www.linear.com/product/LTC2412
http://www.linear.com/product/LTC2413

http://www.linear.com/product/LTC2412#demoboards
http://www.linear.com/product/LTC2413#demoboards


Copyright 2018(c) Analog Devices, Inc.

All rights reserved.

Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
 - Redistributions of source code must retain the above copyright
   notice, this list of conditions and the following disclaimer.
 - Redistributions in binary form must reproduce the above copyright
   notice, this list of conditions and the following disclaimer in
   the documentation and/or other materials provided with the
   distribution.
 - Neither the name of Analog Devices, Inc. nor the names of its
   contributors may be used to endorse or promote products derived
   from this software without specific prior written permission.
 - The use of this software may or may not infringe the patent rights
   of one or more patent holders.  This license does not release you
   from the requirement that you obtain separate licenses from these
   patent holders to use this software.
 - Use of the software either in source or binary form, must be run
   on or directly connected to an Analog Devices Inc. component.

THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, INTELLECTUAL PROPERTY RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/

//! @ingroup Analog_to_Digital_Converters
//! @{
//! @defgroup LTC2412 LTC2412: 2-Channel Differential Input 24-Bit No Latency Delta Sigma ADC
//! @}

/*! @file
    @ingroup LTC2412
    Library for LTC2412: 2-Channel Differential Input 24-Bit No Latency Delta Sigma ADC
*/

#include <stdint.h>
#include <Arduino.h>
#include "Linduino.h"
#include "LT_SPI.h"
#include "LTC2412.h"
#include <SPI.h>

int8_t LTC2412_EOC_timeout(uint8_t cs, uint16_t miso_timeout)
// Checks for EOC with a specified timeout
{
  uint16_t timer_count = 0;             // Timer count for MISO
  output_low(cs);                       //! 1) Pull CS low
  while (1)                             //! 2) Wait for SDO (MISO) to go low
  {
    if (input(MISO) == 0) break;        //! 3) If SDO is low, break loop
    if (timer_count++>miso_timeout)     // If timeout, return 1 (failure)
    {
      output_high(cs);                  // Pull CS high
      return(1);
    }
    else
      delay(1);
  }
  return(0);
}

void LTC2412_read(uint8_t cs, uint32_t *adc_code)
// Reads the LTC2412 result
{
  LT_union_int32_4bytes data, command;
  command.LT_byte[3] = 0;
  command.LT_byte[2] = 0;
  command.LT_byte[1] = 0;
  command.LT_byte[0] = 0;

  output_low(cs);                                                       //! 1) Pull CS low
  spi_transfer_block(cs, command.LT_byte, data.LT_byte, (uint8_t)4);    //! 2) Transfer 4 bytes
  output_high(cs);                                                      //! 3) Pull CS high
  *adc_code = data.LT_int32;
}

float LTC2412_code_to_voltage(int32_t adc_code, float LTC2412_lsb , int32_t LTC2412_offset_code)
// Calculates the LTC2412 input voltage
{
  float adc_voltage;
  uint8_t sign;
  sign = (uint8_t)(adc_code >> 29);
  sign = sign & 1;
  adc_code = adc_code>>5;                                           //! 1) Bit-shift ADC code to the right 5 bits
  adc_code = adc_code & 0xFFFFFF;
  if (!sign)
    adc_code -= 16777216;                                              //! 2) Convert ADC code from offset binary to binary
  adc_voltage=((float)adc_code+LTC2412_offset_code)*(LTC2412_lsb);  //! 3) Calculate voltage from ADC code, lsb, offset.
  return(adc_voltage);
}