/*!
LTC2945: 12-Bit Wide Range Power Monitor

@verbatim

The LTC2945 is a rail-to-rail system monitor that measures current, voltage, and
power. It features an operating range of 2.7V to 80V and includes a shunt
regulator for supplies above 80V to allow flexibility in the selection of input
supply. The current measurement range of 0V to 80V is independent of the input
supply. An onboard 0.75% accurate 12-bit ADC measures load current, input
voltage and an auxiliary external voltage. A 24-bit power value is generated by
digitally multiplying the measured 12-bit load current and input voltage data.
Minimum and maximum values are stored and an overrange alert with programmable
thresholds minimizes the need for software polling. Data is reported via a
standard I2C interface. Shutdown mode reduces power consumption to 20uA.

@endverbatim

http://www.linear.com/product/LTC2945

http://www.linear.com/product/ltc2945#demoboards


Copyright 2018(c) Analog Devices, Inc.

All rights reserved.

Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
 - Redistributions of source code must retain the above copyright
   notice, this list of conditions and the following disclaimer.
 - Redistributions in binary form must reproduce the above copyright
   notice, this list of conditions and the following disclaimer in
   the documentation and/or other materials provided with the
   distribution.
 - Neither the name of Analog Devices, Inc. nor the names of its
   contributors may be used to endorse or promote products derived
   from this software without specific prior written permission.
 - The use of this software may or may not infringe the patent rights
   of one or more patent holders.  This license does not release you
   from the requirement that you obtain separate licenses from these
   patent holders to use this software.
 - Use of the software either in source or binary form, must be run
   on or directly connected to an Analog Devices Inc. component.

THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, INTELLECTUAL PROPERTY RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/

//! @ingroup Power_Monitors
//! @{
//! @defgroup LTC2945 LTC2945: 12-Bit Wide Range Power Monitor
//! @}

/*! @file
   @ingroup LTC2945
   Library for LTC2945 12-Bit Wide Range Power Monitor
*/

#include <Arduino.h>
#include <stdint.h>
#include "Linduino.h"
#include "LT_I2C.h"
#include "LTC2945.h"
#include <Wire.h>

// Write an 8-bit code to the LTC2945.
int8_t LTC2945_write(uint8_t i2c_address, uint8_t adc_command, uint8_t code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  int32_t ack;

  ack = i2c_write_byte_data(i2c_address, adc_command, code);

  return ack;

}

// Write a 16-bit code to the LTC2945.
int8_t LTC2945_write_16_bits(uint8_t i2c_address, uint8_t adc_command, uint16_t code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  int8_t ack;

  ack = i2c_write_word_data(i2c_address, adc_command, code);
  return(ack);
}

// Write a 24-bit code to the LTC2945.
int8_t LTC2945_write_24_bits(uint8_t i2c_address, uint8_t adc_command, int32_t code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  int8_t ack;

  LT_union_int32_4bytes data;
  data.LT_int32 = code;

  ack = i2c_write_block_data(i2c_address, adc_command, (uint8_t) 3, data.LT_byte);

  return(ack);
}

// Reads an 8-bit adc_code from LTC2945
int8_t LTC2945_read(uint8_t i2c_address, uint8_t adc_command, uint8_t *adc_code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  int32_t ack;

  ack = i2c_read_byte_data(i2c_address, adc_command, adc_code);

  return ack;
}

// Reads a 12-bit adc_code from LTC2945
int8_t LTC2945_read_12_bits(uint8_t i2c_address, uint8_t adc_command, uint16_t *adc_code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  // Use union type defined in Linduino.h to combine two uint8_t's (8-bit unsigned integers) into one uint16_t (unsigned 16-bit integer)
  // Then, shift by 4 bits and return in *adc_code
  int32_t ack;

  ack = i2c_read_word_data(i2c_address, adc_command, adc_code);

  *adc_code >>= 4;
  return ack;
}

// Reads a 16-bit adc_code from LTC2945
int8_t LTC2945_read_16_bits(uint8_t i2c_address, uint8_t adc_command, uint16_t *adc_code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  int32_t ack;

  ack = i2c_read_word_data(i2c_address, adc_command, adc_code);

  return ack;
}

// Reads a 24-bit adc_code from LTC2945
int8_t LTC2945_read_24_bits(uint8_t i2c_address, uint8_t adc_command, int32_t *adc_code)
// The function returns the state of the acknowledge bit after the I2C address write. 0=acknowledge, 1=no acknowledge.
{
  int8_t ack;

  LT_union_int32_4bytes data;

  ack = i2c_read_block_data(i2c_address, adc_command, (uint8_t)3, data.LT_byte);

  *adc_code = 0x0FFFFFF & data.LT_int32;
  return(ack);
}

// Calculate the LTC2945 VIN voltage
float LTC2945_VIN_code_to_voltage(uint16_t adc_code, float LTC2945_VIN_lsb)
// Returns the VIN Voltage in Volts
{
  float voltage;
  voltage = (float)adc_code*LTC2945_VIN_lsb;    //! 1) Calculate voltage from code and lsb
  return(voltage);
}

// Calculate the LTC2945 ADIN voltage
float LTC2945_ADIN_code_to_voltage(uint16_t adc_code, float LTC2945_ADIN_lsb)
// Returns the ADIN Voltage in Volts
{
  float adc_voltage;
  adc_voltage = (float)adc_code*LTC2945_ADIN_lsb;   //! 1) Calculate voltage from code and ADIN lsb
  return(adc_voltage);
}

// Calculate the LTC2945 current with a sense resistor
float LTC2945_code_to_current(uint16_t adc_code, float resistor, float LTC2945_DELTA_SENSE_lsb)
// Returns the LTC2945 current
{
  float voltage, current;
  voltage = (float)adc_code*LTC2945_DELTA_SENSE_lsb;    //! 1) Calculate voltage from ADC code and delta sense lsb
  current = voltage/resistor;                           //! 2) Calculate current, I = V/R
  return(current);
}

// Calculate the LTC2945 power
float LTC2945_code_to_power(int32_t adc_code, float resistor, float LTC2945_Power_lsb)
// Returns The LTC2945 power
{
  float voltage, power;
  voltage = (float)adc_code*LTC2945_Power_lsb;  //! 1) Calculate V^2 from ADC code and power lsb
  power = voltage/resistor;                     //! 2) Calculate Power, P = V^2/R
  return(power);
}

// Calculate the LTC2945 power with the ADIN
float LTC2945_code_to_ADIN_power(int32_t adc_code, float resistor, float LTC2945_ADIN_DELTA_SENSE_lsb)
// Returns the LTC2945 power with the ADIN
{
  float voltage, power;
  voltage=(float)adc_code*LTC2945_ADIN_DELTA_SENSE_lsb;   //! 1) Calculate V^2 from ADC code and ADIN delta sense lsb
  power = voltage/resistor;                               //! 2) Calculate Power, P = V^2/R
  return(power);
}