; Renishaw Productivity+ Custom Macro ; Do NOT remove the preceeding line or this macro will not load ; Definition File for Non-Contact Toolsetting Tool Length/Diameter Setting ; Version: 0.01. [FileType] ; Do NOT remove this section or this Custom Macro will not load Product Renishaw Productivity+ File Custom Macro Version 0.07.002 [MachineType] MACHINETYPE OKUMA [Toolsetting Type] "Non Contact" ; Definition File Language - language of displayable text strings in this file [Language] English ; Existing Menu Item in application that Custom Macro name and its Parent Menu are to appear under ; FIELD CAN BE OMITTED [Existing Menu] "Tool setting" ; Parent Menu - used as parent menu item text ; FIELD CAN BE OMITTED [Parent Menu] "Non Contact (NC1, NC2, NC4...)" ; Custom Macro Name - used as menu item text. ID MUST BE UNIQUE FOR EACH CUSTOM MACRO! ; FIELD IS COMPULSORY [Custom Macro] ; Name ID "Tool Length/Diameter (Okuma)" 48870 ; This field specifies the default name given to a statement of this type ; The name must NOT include any of the following characters and cannot start with a numeric character ; {}[]/\:<>@~#-=+()*&^%$£!"`¬|;,.'? [Default Statement Name] "Length_Diameter" ; Name or Program Number of macro [MacroID] 9862 ; Properties - Do not use IDs 1-19 ; Name ID Datatype Default Range Category Output Parameter Metafile ID (optional) Help Text [Properties] "Measurement Type (B)" 20 MEAS_TYPE 1 {NA} 100 CM_B 11058 "Type of Measurement to perform." "Do Tolerance Check (H)" 21 YESNO NO {NA} 100 - 11058 "Set this value to 'Yes' to perform a tolerance check and pass the tolerance value to the tool setting macro." "Tolerance (H)" 22 LINEAR 0.0 GT0 100 CM_H 11058 "Tolerance value that defines when the tool length/diameter is out of tolerance." "Prevent Out of Tolerance Alarms (M1)" 23 YESNO NO {NA} 100 - 11058 "Tool out of tolerance flag. Setting this value to 'Yes' will not raise an Out of Tolerance alarm, but set a variable flag when tool is out of tolerance." "Flag to Prevent Out Of Tol Alarms (M1)" 45 INT 1 GT0:LE999 100 CM_M 11058 "The default value for this function is 1 and does not need to be altered. The Out Of Tol alarm will be prevented and a variable flag set if the tool is out of tolerance." "Use Default Overtravel Distance (Q)" 24 YESNO YES {NA} 100 - 11058 "Use the toolsetting macro's default value for Overtravel Distance. Set this value to 'No' to specify a custom Overtravel Distance." "Overtravel Distance (Q)" 25 LINEAR 5.0 {NA} 100 CM_Q 11058 "Overtravel distance is the distance through the beam that the tool is permitted to move before a Beam Not Cut alarm is initiated." "Use Default Spindle Speed (S)" 26 YESNO YES {NA} 100 - 11058 "Use the toolsetting macro's default value for Spindle Speed. Set this value to 'No' to specify a custom Spindle Speed." "Spindle Speed (S)" 27 INT 3150 GE1 100 CM_S 11058 "Spindle speed at which length/diameter measurement takes place. Measurement cycles are optimised for a spindle speed of 3150 rev/min, though some tools (e.g. those that are unbalanced or large) must be run at slower speeds. It is responsibility of the User to set the spindle speed accordingly, with the minimum speed being 800 rev/min." "Use Experience Value For Length (J)" 28 YESNO NO {NA} 101 - 11058 "Set this value to 'Yes' to pass the Experience Value For Length parameter to the macro." "Experience Value For Length (J)" 29 LINEAR 0.0 {NA} 101 CM_J 11058 "This value is the difference between the measured length of the tool and the effective length when the tool is under load during the cutting process." "Use Current Tool Change ID (T)" 30 YESNO YES {NA} 101 - 11058 "When this value is set to 'Yes' the current tool change ID is used as the Length Offset Number. When set to 'No' you can specfy a Length Offset number." "Tool Length Offset Number (T)" 31 INT 0 GT0:LE999 101 CM_T 11058 "Length Offset Number. This is the offset location in which the measured tool length is stored." "Use A Radial Step-over (Y)" 43 YESNO NO {NA} 101 - 11058 "Set to 'Yes' to enter a value for the offset across the beam at which length measurement takes place. Set to 'No' to use default." "Radial Step-over (Y)" 32 LINEAR 0. {NA} 101 CM_Y 11058 "Radial step-over for length setting. This is the offset across the beam at which length measurement takes place. The value must be less than the radius of the tool. The tool always comes down first on the beam centre-line." "Use Diameter Offset Number (D)" 41 YESNO NO {NA} 102 - 11058 "Set this value to 'Yes' to pass an offset location in which the measured tool diameter/radius is stored." "Tool Diameter Offset Number (D)" 33 INT 0 GT0:LE999 102 CM_D 11058 "Diameter Offset Number. This is the offset location in which the measured tool diameter/radius is stored." "Use Experience Value For Diameter (I)" 34 YESNO NO {NA} 102 - 11058 "Set this value to 'Yes' to pass the Experience Value For Diameter parameter to the macro." "Experience Value For Diameter (I)" 35 LINEAR 0.0 {NA} 102 CM_I 11058 "This value is the difference between the measured diameter/radius of the tool and the actual diameter/radius when the tool is under load during the cutting process." "Specify Tool Diameter (R)" 36 YESNO NO {NA} 102 - 11058 "When setting the tool's diameter/radius you do not have to specify the nominal diameter of the tool as the macro will use a predefined maximum value. However by specifying a nominal diameter the cycle time can be reduced." "Tool Diameter (R)" 37 LINEAR 0.0 GT0 102 CM_R 11058 "This is the nominal diameter of the tool." "Use Spindle Axis Search Distance (X)" 40 YESNO NO {NA} 102 - 11058 "Set this value to 'Yes' to pass a search distance to the macro" "Spindle Axis Search Distance (X)" 38 LINEAR 0 GT0 102 CM_X 11058 "Spindle Axis Search Distance. This defines a search distance above the Z-input measuring height, which can be used to find a radial high spot on the cutter. It is suitable for single-point boring bars and cutters with irregular radial profiles. Cycle time is increased using this input. "Include a Measuring Height (Z)" 44 YESNO NO {NA} 102 - 11058 "Measuring height of tool. This is the Z-axis position from the end face of the tool at which measurement takes place." "Measuring Height (Z)" 39 LINEAR 5.0 {NA} 102 CM_Z 11058 "Measuring height of tool. This is the Z-axis position from the end face of the tool at which measurement takes place." [Visibility] PROPERTIES 101 CTRL_PROPS 20 ("Measurement Type") CTRL_VALUES 1 ("Tool Length") CTRL_VALUES 3 ("Tool Length and Radius") PROPERTIES 102 CTRL_PROPS 20 ("Measurement Type") CTRL_VALUES 2 ("Tool Radius") CTRL_VALUES 3 ("Tool Length and Radius") PROPERTIES 22 CTRL_PROPS 21 ("Do Tolerance Check") CTRL_VALUES 2 ("YES") PROPERTIES 23 CTRL_PROPS 21 ("Do Tolerance Check") CTRL_VALUES 2 ("YES") PROPERTIES 39 CTRL_PROPS 44 ("Include a Measuring Height (Z)") CTRL_VALUES 2 ("NO") PROPERTIES 32 CTRL_PROPS 43 ("Use A Radial Step-over (Y)") CTRL_VALUES 2 ("NO") PROPERTIES 25 CTRL_PROPS 24 ("Use Default Overtravel Distance") CTRL_VALUES 1 ("NO") PROPERTIES 27 CTRL_PROPS 26 ("Use Default Spindle Speed ") CTRL_VALUES 1 ("NO") PROPERTIES 29 CTRL_PROPS 28 ("Use Experience Value For Length") CTRL_VALUES 2 ("YES") PROPERTIES 31 CTRL_PROPS 30 ("Use Current Tool Change ID") CTRL_VALUES 1 ("NO") PROPERTIES 35 CTRL_PROPS 34 ("Use Experience Value For Diameter") CTRL_VALUES 2 ("YES") PROPERTIES 37 CTRL_PROPS 36 ("Specify Tool Diameter") CTRL_VALUES 2 ("YES") PROPERTIES 38 CTRL_PROPS 40 ("Use Spindle Axis Search Distance") CTRL_VALUES 2 ("YES") PROPERTIES 33 CTRL_PROPS 41 ("Use Diameter Offset Number") CTRL_VALUES 2 ("YES") PROPERTIES 45 CTRL_PROPS 23 ("Prevent Out of Tolerance Alarms (M1)") CTRL_VALUES 2 ("YES") [Enums] ; N.B. When post processing, the selected enum item ID will be outputted with the Output Parameter. ; e.g. enum type : YESNO ; selected enum item : YES ; enum item value : 1 ; Output Parameter : CM_B ; Output = B1 ; ID Index (order in which they will appear) ENUM_NAME MEAS_TYPE ENUM_ITEM "Tool Length" 1 0 ENUM_ITEM "Tool Radius/Diameter" 2 1 ENUM_ITEM "Tool Length and Radius" 3 2 ENUM_NAME TOL_ALARM ENUM_ITEM "Yes" 0 0 ENUM_ITEM "No" 1 1 [Categories] ; Name ID "Nominals" 100 "Length Measurement" 101 "Radius Measurement" 102 [Resources] ; File name of resource DLL containing metafiles (optional) PP_tsToolSettingRes.dll ; The post processor section to call when post processing occurs [Post Section] TOOLSETTING_CUSTOMMACRO