Forum
Visit the forum to see what the rest of the Mastercam community is talking about.
The table below lists issues addressed in Mastercam 2026 and its updates. Use the controls below to search within the table or to sort it by column header.
You can use the side menu to view a specific category, download previous Release Notes PDFs, or navigate to additional Mastercam resources.
| Number | Release | Category | Description | Date |
|---|---|---|---|---|
| R-41180 | PB 4 | CAD | In Transform (Translate), associated toolpaths are not moved but still show as clean. | 4/28/2025 |
| R-41700 | PB 4 | Milling Toolpaths | Make changes to Deburr 5-axis to differentiate it from Deburr 3-axis. | 4/28/2025 |
| R-41608 | PB 4 | Milling Toolpaths | In Chamfer Drill, holes are dropped on regeneration in Mastercam 2025 and 2026. | 4/28/2025 |
| R-41579 | PB 4 | Milling Toolpaths | In Hole making selection, inconsistent window selection behavior in 2026. | 4/28/2025 |
| R-41578 | PB 4 | Milling Toolpaths | In Drill, hole direction flips on some holes when selected. | 4/28/2025 |
| R-41577 | PB 4 | Milling Toolpaths | In hole making with voids, there are selection and hole segments issues. | 4/28/2025 |
| R-41576 | PB 4 | Milling Toolpaths | In Stock Model, remove pathType5 usage for port back to 2026. | 4/28/2025 |
| R-41449 | PB 4 | Milling Toolpaths | In Safety Zone, the graphical preview moves every time you edit the operation. | 4/28/2025 |
| R-41425 | PB 4 | Milling Toolpaths | Barrel tool cuts too deep when cut length is more than the barrel. | 4/28/2025 |
| R-41417 | PB 4 | Milling Toolpaths | 2D Area Mill loses its leads if regenerated with a Model Chamfer toolpath. | 4/28/2025 |
| R-41416 | PB 4 | Milling Toolpaths | 2D Dynamic and Area finish passes do not output spring passes with multiple regions. | 4/28/2025 |
| R-41415 | PB 4 | Milling Toolpaths | Circle mill spring passes are not output if Start at center is off. | 4/28/2025 |
| R-41357 | PB4 | Milling Toolpaths | With Deburr 3-axis and Mill-Turn, linking the T-Plane is not working correctly. | 4/28/2025 |
| R-41273 | PB4 | Milling Toolpaths | In hole making, multiple hole-selection issues. | 4/28/2025 |
| R-41210 | PB4 | Milling Toolpaths | Allow tapered holes checkbox doesn't work well with window selection. | 4/28/2025 |
| R-41209 | PB 4 | Milling Toolpaths | With Safety Zone, a bad path results when the tool axes of multiple holes are aligned with each other. | 4/28/2025 |
| R-41208 | PB 4 | Milling Toolpaths | With saving defaults, Mastercam crashes after a sequence of add and delete. | 4/28/2025 |
| R-41183 | PB 4 | Milling Toolpaths | In Unified Multiaxis, Mastercam crashes when you view the Angle Range page. | 4/28/2025 |
| R-41159 | PB 4 | Milling Toolpaths | Regenerating a Swept 2D toolpath in 2025 causes the toolpath to offset drastically. | 4/28/2025 |
| R-40973 | PB 4 | Licensing | Mastercam 2025 Update 5 launcher and shortcut command for network software license is not working. | 4/28/2025 |
| R-40974 | PB 4 | CAD | Associated toolpaths are not moved but still show as clean. | 4/28/2025 |
| R-41197 | PB 4 | Machine Systems | The part length value seems incorrect when stock is solid or STL. | 4/28/2025 |
| R-41473 | PB 4 | CAD | Surface was slow to delete. | 4/28/2025 |
| R-41363 | PB 4 | CAD | Mastercam 2025 crashes when opening a file. | 4/28/2025 |
| R-41358 | PB 4 | Milling Toolpaths | Surface Rough Pocket regeneration crashes to the Desktop. | 4/28/2025 |
| R-41277 | PB 4 | Backplot/Verify/Simulation | Exporting a Mastercam file with grouped entities to a DXF file creates duplicate entities. | 4/28/2025 |
| R-41348 | PB 4 | Backplot/Verify/Simulation | In Simulation, there is a verify error when lead in/out is not used. | 4/28/2025 |
| R-40681 | PB 4 | Milling Toolpaths | Errors or exceptions were discovered during generic testing with random parts. | 4/28/2025 |
| R-40681 | PB 4 | Milling Toolpaths | 2D Pocket that uses the open pocket cut method is machining outside the selected chains. | 4/28/2025 |
| R-40342 | PB 4 | Milling Toolpaths | With Contour, the spindle speed is wrong on the second pass and regeneration does not fix it. | 4/28/2025 |
| R-41608 | PB 4 | Milling Toolpaths | Selected holes were dropped after reselection from previous version files. | 4/28/2025 |
| R-39063 | PB 2 | Milling Toolpaths | When you use Toolpath Hole Definition, the hole selection changes after toolpath generation. | 3/6/2025 |
| R-38550 | PB 2 | CAD | With Surfaces (Surfaces from Solid), when you press [Enter] after solid selection, the function exits. | 3/6/2025 |
| R-41034 | PB 2 | CAD | Mastercam is hanging up after running Verify. | 3/6/2025 |
| R-36620 | PB 2 | CAD | With Drafting, when you change the level, create the note, and exit, the level returns to the original number. | 3/6/2025 |
| R-40676 | PB 2 | CAD | When you delete all geometry and dimensions, a warning prompt appears for each dimension. | 3/6/2025 |
| R-37845 | PB 1 | Milling Toolpaths | Mastercam crashes when going to the Cut Patterns page of a Unified operation with this Lens Barrel tool. | 2/18/2025 |
| R-40611 | PB 1 | Milling Toolpaths | In Unified Parallel, setting the number of cuts to 1 gives us the last pass instead of the first. | 2/18/2025 |
| R-40330 | PB 1 | Milling Toolpaths | Deburr is not maintaining climb cutting. | 2/18/2025 |
| R-39543 | PB 1 | Milling Toolpaths | Hole Making needs better method for handling earlier files and coaxial holes. | 2/18/2025 |
| R-40092 | PB 1 | Milling Toolpaths | 2D contour causes a gouge with Keep tool down. | 2/18/2025 |
| R-40252 | PB 1 | Milling Toolpaths | With 2D Thread Mill, setting Arc sweep to greater than 180 degrees creates an extra unexpected move. | 2/18/2025 |
| R-38968 | PB 1 | Milling Toolpaths | A Drill 5-axis toolpath that has a non-zero depth, tip comp, and safety zone active starts at the wrong depth when regenerated in 2025. | 2/18/2025 |
| R-39544 | PB 1 | Milling Toolpaths | With Hole Making, voids are not detected in holes. | 2/18/2025 |
| R-39507 | PB 1 | Milling Toolpaths | The Model Chamfer toolpath fails to regenerate when the clearance value and no workholding entities are selected. | 2/18/2025 |
| R-40342 | PB 1 | Milling Toolpaths | With 2D Contour, the spindle speed is wrong on the second pass and regenerating does not fix it. | 2/18/2025 |
| R-39799 | PB 1 | Milling Toolpaths | In the Unified toolpath, the Max projection distance field is not available in Mastercam 2025. | 2/18/2025 |
| R-32745 | PB 1 | Milling Toolpaths | In Toolpath/surface selection, Machining set to Allselects nothing when creating the same toolpath. | 2/18/2025 |
| R-38160 | PB 1 | Milling Toolpaths | 2D contour trims lead in/out with Adjust start/end of contour in Mastercam 2025. | 2/18/2025 |
| R-38763 | PB 1 | Milling Toolpaths | With hole segments, non-Top holes without history display incorrectly. | 2/18/2025 |
| D-14631 | PB 1 | Milling Toolpaths | Surface rough pocket gouges. | 2/18/2025 |
| D-13697 | PB 1 | Milling Toolpaths | 2D Pocket using Open pocket cut method is machining outside selected chains (+7) | 2/18/2025 |
| R-30408 | PB 1 | Milling Toolpaths | Using 3-axis motion, Stock Model cuts farther than the tool. | 2/18/2025 |
| R-38425 | PB 1 | CAD | Using the translator, an Inventor assembly opens improperly. | 2/18/2025 |
| R-38567 | PB 1 | CAD | When offsetting geometry, Mastercam no longer shows before and after colors. | 2/18/2025 |
| R-35389 | PB 1 | CAD | In Transform (Project), a 3D chain of lines, arcs, and splines projects flat with gaps between some entities. | 2/18/2025 |
| R-38755 | PB 1 | CAD | A Test Surface app gives a false positive reading for a normal error. | 2/18/2025 |
| R-34917 | PB 1 | CAD | With a very small part, Fillet to Surfaces is unable to put a 0.08-mm constant fillet. | 2/18/2025 |
| R-35766 | PB 1 | CAD | Modify length with Break on does not work properly when you pick a spline less then 0.4 inches. | 2/18/2025 |
| R-36986 | PB 1 | CAD | An Inventor 2024 assembly comes into Mastercam disassembled. | 2/18/2025 |
| R-38506 | PB 1 | CAD | When importing a file with Create hole operations on, arcs are not created as they would if the option was off. | 2/18/2025 |
| R-40734 | PB 1 | CAD | Solids get corrupted when you use Model Prep's Remove Fillets. | 2/18/2025 |
| R-40732 | PB 1 | CAD | With Transform (Geometry Nesting), placing a label on top of a solid is not working. | 2/18/2025 |
| R-40128 | PB 1 | CAD | When using Curve Slice by Plane, pressing enter does not select your geometry. | 2/18/2025 |
| R-40442 | PB 1 | CAD | Clicking Undo after saving causes geometry to move. | 2/18/2025 |
| R-40481 | PB 1 | CAD | Mastercam crashes when you adjust fillet size via spinners. | 2/18/2025 |
| R-39731 | PB 1 | CAD | With a Parasolid X_T assembly import, level names come in differently from Mastercam 2024. | 2/18/2025 |
| S-117926 | PB 1 | CAD | Delete entity speed Improvements. | 2/18/2025 |
| R-37909 | PB 1 | CAD | With Surface Draft, Mastercam now can flip the normal on all surfaces along the drive chain. | 2/18/2025 |
| R-39805 | PB 1 | Backplot/Verify/Simulation | Simulation shows the wrong operation order. | 2/18/2025 |
| R-39862 | PB 1 | Backplot/Verify/Simulation | In Verify, Add to current verification option gives the warning "Please select a valid operation for simulation" in Lathe operations. | 2/18/2025 |
| R-40401 | PB 1 | Backplot/Verify/Simulation | In Simulation, the tool holder is in the wrong position. | 2/18/2025 |
| R-40653 | PB 1 | Backplot/Verify/Simulation | In Mill-Turn Simulation, the error "... facing wrong direction for C1" appears in the report window. | 2/18/2025 |
| R-40777 | PB 1 | Backplot/Verify/Simulation | When you change the shank cross section to a round, Mastercam flips the tool orientation 90 degrees in Backplot. | 2/18/2025 |
| R-40163 | PB 1 | Machine Systems | You cannot use a single-quote character (') in a comment that is part of a transform. | 2/18/2025 |
| R-40712 | PB 1 | Machine Systems | Adding a new state in Code Expert causes an error. | 2/18/2025 |
| R-39242 | TP 4 | Milling Toolpaths | The Extend/Trim Side extensions in the Morph-style Unified toolpath does not extend as expected. | 1/20/2025 |
| R-39914 | TP 4 | Milling Toolpaths | In Rotary Advanced, Intermediate slices is not working in a part file from Mastercam 2022. | 1/20/2025 |
| R-39983 | TP 4 | Milling Toolpaths | The Pocketing toolpath does not read the tool's spindle direction. | 1/20/2025 |
| R-40229 | TP 4 | Milling Toolpaths | Corrected instances of the Convert to 5-Axis toolpath are no longer projecting to the supplied surface. | 1/20/2025 |
| R-40216 | TP 4 | Milling Toolpaths | In Deburr 3-axis, a disjointed toolpath should be continuous with Dove mill. | 1/20/2025 |
| R-40335 | TP 4 | Milling Toolpaths | Machine Simulation has a refactored code regression in Mastercam 2025/26 that causes gouging. | 1/20/2025 |
| R-40382 | TP 4 | Milling Toolpaths | Dynamic Mill and Area Mill outputs finish passes in the wrong Z location with profile ramp entry. | 1/20/2025 |
| R-40009 | TP 4 | Milling Toolpaths | The Area Roughing rest calculation takes five times longer to regenerate. | 1/20/2025 |
| D-16200 | TP 4 | Milling Toolpaths | In Dynamic Contour, the contour wall page entry fields are limited to three decimal places. | 1/20/2025 |
| R-17529 | TP 4 | Milling Toolpaths | Surface Rough Pocket cuts through the part. | 1/20/2025 |
| D-16888 | TP 4 | Milling Toolpaths | Surface Rough Pocket's parallel spiral method gouges the part. | 1/20/2025 |
| R-37906 | TP 4 | Milling Toolpaths | Dynamic Mill and Blend Mill now have a first-pass spindle-speed control. | 1/20/2025 |
| R-39956 | TP 4 | CAD | With surfaces, Trim to Plane leaves geometry behind. | 1/20/2025 |
| R-37552 | TP 4 | CAD | In toolpath nesting, use the part name as the label and remove unnecessary information. | 1/20/2025 |
| R-36556 | TP 4 | CAD | With Trim (Divide), splines create additional geometry when you use power drag mode. | 1/20/2025 |
| R-38444 | TP 4 | CAD | You can now use a tighter tolerance than 0.0001 when you create an ellipse with arcs. | 1/20/2025 |
| R-38941 | TP 4 | Tooling | The Assembly Has Changed dialog box is only presented the first time you edit the tool's SFM option. | 1/20/2025 |
| R-40308 | TP 4 | Turning Toolpaths | View/Show Tool does not work in Mastercam 2025. | 1/20/2025 |
| R-38155 | TP 4 | Tooling | In Tool Manager, when you copy holders to a blank library, "Copy of" gets added to the start of the names. | 1/20/2025 |
| R-39419 | TP 4 | Turning Toolpaths | In Lathe drilling, when you change the rotation type, linking depths also change. | 1/20/2025 |
| R-40068 | TP 4 | Tooling | When editing an operation's tools, tool offsets do not update for one operation, while all other ops update correctly. | 1/20/2025 |
| R-37440 | TP 4 | Tooling | Verify shows the highfeed tool in the wrong location on the holder. | 1/20/2025 |
| R-39085 | TP 4 | Milling Toolpaths | In Triangular Mesh paths, the automatic clearance plane still appears to use the user-defined value. | 12/3/2024 |
| R-39382 | TP 4 | Milling Toolpaths | Mastercam throws an unknown exception when trying to compute a Unified toolpath in a specific part. | 12/3/2024 |
| R-39773 | TP 4 | Milling Toolpaths | In the Unified toolpath's tool axis control, the Gradual contact height % change checkbox does not retain its state. | 12/3/2024 |
| R-38883 | TP 4 | Milling Toolpaths | In the Deburr 3-axis toolpath, a cross drilled hole does not create a deburr toolpath. | 12/3/2024 |
| R-32329 | TP 4 | Milling Toolpaths | In Drill 5-axis, the stock and safety zone create extra motion. | 12/3/2024 |
| R-35197 | TP 4 | Milling Toolpaths | The 3D Blend toolpath hangs when calculating blend passes. | 12/3/2024 |
| R-37778 | TP 4 | Milling Toolpaths | In the OptiRough toolpath, step-ups are missing some flats. | 12/3/2024 |
| R-38812 | TP 4 | Milling Toolpaths | In the 2D Pocket toolpath with an open pocket, Use standard pocket for closed chains is always enabled after computing the toolpath. | 12/3/2024 |
| R-39307 | TP 4 | Milling Toolpaths | In the 2D Dynamic toolpath, finish passes do not finish the entire pocket with an air region. | 12/3/2024 |
| R-39375 | TP 4 | Milling Toolpaths | A toolpath with compensation set to Control displays incorrectly when regenerating two toolpaths on different planes. | 12/3/2024 |
| R-39695 | TP 4 | Milling Toolpaths | In the Area Roughing toolpath, the Keep tool down between Z depths option is failing. | 12/3/2024 |
| R-39826 | TP 4 | Milling Toolpaths | A hole-making toolpath picks the wrong hole to process. | 12/3/2024 |
| R-39781 | TP 4 | Milling Toolpaths | In 5-axis Drill, the home/ref position's tool-vector direction is pointing the only direction we don't want. | 12/3/2024 |
| R-39747 | TP 4 | Milling Toolpaths | In the Dynamic Mill toolpath, Minimize Burial on a finish pass creates invalid full arc errors when posting | 12/3/2024 |
| R-39930 | TP 4 | Milling Toolpaths | In Mill Pocket re-machining, Apply entry/exit curves to rough passes does not work. | 12/3/2024 |
| R-39996 | TP 4 | Milling Toolpaths | In the classic 3D toolpaths, using Show causes solid to disappear. | 12/3/2024 |
| R-40082 | TP 4 | Milling Toolpaths | In the NCI, the Dynamic Finish pass causes full-arc flag issues. | 12/3/2024 |
| R-39658 | TP 4 | Milling Toolpaths | With the Waterline toolpath, toolpath regeneration time increased drastically from prior versions. | 12/3/2024 |
| R-33833 | TP 4 | Milling Toolpaths | Misc Value changes do not post unless operations are forcibly regenerated. | 12/3/2024 |
| R-36989 | TP 4 | Milling Toolpaths | With an imported Drill toolpath, the Retract value is changed. | 12/3/2024 |
| R-39516 | TP 4 | Milling Toolpaths | The Drill toolpath's Retract value changes when opened in a newer Mastercam version. | 12/3/2024 |
| D-56145 | TP 4 | Milling Toolpaths | When using single-point drive curves, regenerating a 3D Blend toolpath results in a regeneration crash or a computational error. | 12/3/2024 |
| D-56150 | TP 4 | Milling Toolpaths | The Blend toolpath hangs when calculating blend passes with a small stepover. | 12/3/2024 |
| D-14743 | TP 4 | Milling Toolpaths | The Raster toolpath does not start at the selected approximate starting point. | 12/3/2024 |
| R-40242 | TP 4 | CAD | Transform Project does not trim geometry to the solid edge. | 12/3/2024 |
| R-39654 | TP 4 | Backplot/Verify/Simulation | Verify produces an error in the input data stream. | 12/3/2024 |
| R-39611 | TP 4 | Backplot/Verify/Simulation | Verify gouges when compensation is set to Control. | 12/3/2024 |
| R-40161 | TP 4 | Backplot/Verify/Simulation | Mill-Turn simulation hangs on initial tool change. | 12/3/2024 |
| R-09875 | TP 4 | Backplot/Verify/Simulation | Enhance Mastercam Simulator to allow you to change the editing text size when you analyze a point and a distance. | 12/3/2024 |
| R-22782 | TP 4 | Backplot/Verify/Simulation | In Verify, add an option to the default STL save function so that it uses the current file save location. | 12/3/2024 |
| R-38640 | TP 4 | Tooling | The shoulder diameter on the Thread Mill toolpath causes a simulation error. | 12/3/2024 |
| R-39253 | TP 4 | Machine Systems | Setting the DNC Machine does not persist in Code Expert. | 12/3/2024 |
| R-40147 | TP 4 | Tooling | A GTC file does not open as an assembly. | 12/3/2024 |
| R-38742 | TP 3 | Milling Toolpaths | When importing drill ops and selecting the same holes, you get different results in Mastercam 2024 and 25. | 11/12/2024 |
| R-39442 | TP 3 | Milling Toolpaths | The OptiRough toolpath is missing the step-up on a small flat area. | 11/12/2024 |
| R-39575 | TP 3 | Milling Toolpaths | In hole-making toolpaths, hole selection is dropping a hole. | 11/12/2024 |
| R-39460 | TP 3 | Milling Toolpaths | In hole-making toolpaths, the diameter of the same hole size is different on one of the holes after regeneration. | 11/12/2024 |
| D-54508 | TP 3 | Milling Toolpaths | The OptiRough toolpath plunges into material. | 11/12/2024 |
| R-39672 | TP 3 | Milling Toolpaths | Dynamic toolpaths have a Taper Pretreatment depth cuts issue. | 11/12/2024 |
| R-36292 | TP 3 | Milling Toolpaths | The Tabs page needs the message "Tabs on Solid Edge selection not supported." | 11/12/2024 |
| S-114996 | TP 3 | Milling Toolpaths | Rearrange Tool page buttons. | 11/12/2024 |
| R-39116 | TP 3 | CAD | In the Solids Manager, when you right-click a solid on an undisplayed level and choose Analyze, Mastercam does not show the Analyze panel. | 11/12/2024 |
| R-39787 | TP 3 | CAD | Undo and Redo causes transformed geometry that is used in a toolpath to change selection. | 11/12/2024 |
| R-37182 | TP 3 | CAD | Mastercam crashes when applying Curve Slice by Plane on a Solid. | 11/12/2024 |
| R-39503 | TP 3 | CAD | Deleting a reference entity no longer shows the operation number. | 11/12/2024 |
| R-39376 | TP 3 | CAD | The Rhino converter translates polylines incorrectly. | 11/12/2024 |
| R-38778 | TP 3 | Backplot/Verify/Simulation | Verify is unable to print with a solid white background. | 11/12/2024 |
| R-39701 | TP 3 | Backplot/Verify/Simulation | Classic Backplot does not recognize a Lathe Rough operation. | 11/12/2024 |
| R-33396 | TP 3 | Backplot/Verify/Simulation | In Verify, dog-leg rapids display differently in Mastercam 2023/2024 compared to 2022. | 11/12/2024 |
| R-38633 | TP 3 | Backplot/Verify/Simulation | Classic Backplot has an issue with feed rate overrides and Arc fit maximum radius. | 11/12/2024 |
| R-38332 | TP 3 | Backplot/Verify/Simulation | In Verify, linear rapid motion no longer shows dog-leg rapids. | 11/12/2024 |
| R-14217 | TP 3 | Backplot/Verify/Simulation | In Mastercam Simulator, clicking on Slow or Fast should alter the speed by 10 percent. | 11/12/2024 |
| R-37075 | TP 3 | Tooling | In classic Backplot, the Lathe insert is outside of the tool holder. | 11/12/2024 |
| R-39266 | TP 3 | Tooling | In Tool Manager, when you view the details of custom inserts, the insert width value is 0 instead of the actual value. | 11/12/2024 |
| R-39501 | TP 3 | Machine Systems | Code Expert 2025 does not allow you to comment line items. | 11/12/2024 |
| R-30899 | TP 3 | Tooling | The level visibility changes when you import a holder from a file. | 11/12/2024 |
| R-39499 | TP 3 | Machine Systems | Add a system token to allow access to the mill holder name in the tool table. | 11/12/2024 |
| R-38601 | TP 3 | Tooling | Set display tool needs a double toggle to turn the display tool on and off. | 11/12/2024 |
| R-39452 | TP 3 | System | Add an option to turn off the solid-edge Autocursor preview. | 11/12/2024 |
| R-39515 | TP 2 | Milling Toolpaths | In Unified with the Project style, the Max Project distance parameter is missing. | 10/8/2024 |
| R-39141 | TP 2 | Milling Toolpaths | 5-Axis thread milling crashes when you select multiple holes in this file. | 10/8/2024 |
| R-39070 | TP 2 | Milling Toolpaths | In 5-Axis thread milling, the safety zone shifts and crashes when you try to fix it. | 10/8/2024 |
| R-37816 | TP 2 | Backplot/Verify/Simulation | Barrel Mill tool does not touch the part in Backplot but does in Verify. | 10/8/2024 |
| R-34602 | TP 2 | Turning Toolpaths | Lathe feed rate in Backplot does not show Inches Per Revolution. | 10/8/2024 |
| D-53949 | TP 2 | Milling Toolpaths | In Unified, the taper-bull-nose-end-mill has a tool compensation issue. | 10/8/2024 |
| D-54560 | TP 1 | Milling Toolpaths | Finish passes in Dynamic Mill produce an unexpected result with Automatic regions. | 10/8/2024 |
| D-09068 | TP 1 | Milling Toolpaths | Make the tool plunge or begin the entry move at the selected point. | 10/8/2024 |
| R-37601 | TP 1 | Machine Systems | When you use a multi-insert turning tool in Mill-Turn with multiple operations, you get an extra reference position. | 10/8/2024 |
| S-114353 | TP 1 | Selection/Chaining | Rework how to pick a solid-arc-edge-center-point. | 10/8/2024 |
| D-55736 | TP 1 | Milling Toolpaths | Safety zone post-calculated drilling variables are incorrect. | 10/8/2024 |
| R-39055 | TP 1 | Machine Systems | Exporting toolpaths to the default mill-turn operations does not work. | 9/17/2024 |
| R-39053 | TP 1 | CAD | Mastercam is hanging up after running Verify. | 9/17/2024 |
| R-39323 | TP 1 | CAD | In Nesting, clicking the Save As button causes an Invalid Extension error | 9/17/2024 |
| R-39119 | TP 1 | Milling Toolpaths | Graphical planes cause a lock-up after the escape key is pressed. | 9/17/2024 |
| R-36608 | TP 1 | Milling Toolpaths | Multiaxis Override Arc Feed Rate fields do not update when Feed rate is changed on the Tool page. | 9/17/2024 |
| R-36545 | TP 1 | Milling Toolpaths | Cannot Regenerate the Surface Rough Pocket Toolpath. | 9/17/2024 |
| R-38314 | TP 1 | Milling Toolpaths | When a Dynamic Rough operation is duplicated in Mastercam 2024, the regeneration times increase for each additional Dynamic Rough. | 9/17/2024 |
| R-36593 | TP 1 | Milling Toolpaths | OptiRough needs Critical Depths parameters. | 9/17/2024 |
| R-38108 | TP 1 | Backplot/Verify/Simulation | Launching Machine Simulation with binned simulation file set causes an unknown error. | 9/17/2024 |
| R-37197 | TP 1 | Toolpath Utilities | Export is not exporting level names. | 9/17/2024 |
| R-37942 | TP 1 | Milling Toolpaths | Mastercam outputs a dynamic finish pass in the wrong z location when using island facing. | 9/17/2024 |
| R-38116 | TP 1 | Milling Toolpaths | The Pocket toolpath violates the input chain. | 9/17/2024 |
| R-25426 | TP 1 | Milling Toolpaths | Area rest roughing gouges the part on Helix moves. | 9/17/2024 |
| R-37237 | TP 1 | Milling Toolpaths | 3D toolpath lead-in gouges selected part geometry. | 9/17/2024 |
| R-36686 | TP 1 | Milling Toolpaths | 3D toolpath ramp angle is incorrect with sweep angle set to 180.0. | 9/17/2024 |
| R-38918 | TP 1 | Milling Toolpaths | The OptiRough toolpath gouges stock upon entry. | 9/17/2024 |
| R-38502 | TP 1 | Milling Toolpaths | The Raster toolpath generates improperly when the cut order is set to regions on this part. | 9/17/2024 |
| R-36438 | TP 1 | Milling Toolpaths | The Pocket toolpath cuts through the surface depending on the stepdown. | 9/17/2024 |
| R-38829 | TP 1 | Milling Toolpaths | The Deburr toolpath's direction axis does not appear to be utilized properly. | 9/17/2024 |
| R-24112 | TP 1 | Milling Toolpaths | 5-axis Pocketing fails to generate the file when set to rest roughing. | 9/17/2024 |
| R-33487 | TP 1 | Milling Toolpaths | 5-axis Pocketing is missing an area when stock-to-leave has two separate values entered. | 9/17/2024 |
| R-31069 | TP 1 | Milling Toolpaths | Port Expert linking moves after the first transform violate geometry. | 9/17/2024 |
| R-28546 | TP 1 | Milling Toolpaths | Unified toolpath parameter changes are saved after they are canceled. | 9/17/2024 |
| R-37524 | TP 1 | General | Add the machine file name to IOF job setup settings. | 9/17/2024 |
| R-37246 | TP 1 | Milling Toolpaths | Advanced Drill does not output the spindle speed. | 9/17/2024 |
| R-37704 | TP 1 | Milling Toolpaths | Advanced Drill spindle-speed change without a manual regeneration outputs incorrect segment speed. | 9/17/2024 |
| R-37596 | TP 1 | Milling Toolpaths | Advanced Drill posts wrong peck amounts. | 9/17/2024 |
| R-37425 | TP 1 | Backplot/Verify/Simulation | Backplot and Verify are incorrect if using Translate NCI coordinates to Machine View with aggregate in the control definition. | 9/17/2024 |
| R-36407 | TP 1 | Backplot/Verify/Simulation | Backplot triggers a Parasolid kernel interface error during Lathe tool generation. | 9/17/2024 |
| R-38552 | TP 1 | Milling Toolpaths | Mastercam crashes when changing to the Tool Axis Control page in Blade Expert. | 9/17/2024 |
| R-37974 | TP 1 | Milling Toolpaths | The block drill blind-hole drilling does not work. | 9/17/2024 |
| R-37308 | TP 1 | Milling Toolpaths | The chain order reverses after you add geometry from one toolpath to another. | 9/17/2024 |
| R-37923 | TP 1 | Milling Toolpaths | Chamfer Drill gives an incorrect depth on a hole with voids. | 9/17/2024 |
| R-38398 | TP 1 | Machine Systems | When you open a Mill-Turn configuration file and replace the chucks, the chuck stock display turns off. | 9/17/2024 |
| R-38430 | TP 1 | Backplot/Verify/Simulation | In classic Backplot, the Chamfer Drill depth shows incorrectly. | 9/17/2024 |
| R-36884 | TP 1 | Backplot/Verify/Simulation | In classic Backplot, the Simulate rotary axis checkbox no longer works. | 9/17/2024 |
| R-38070 | TP 1 | Milling Toolpaths | Closing the Multiaxis toolpath dialog crashes Mastercam. | 9/17/2024 |
| R-37466 | TP 1 | Machine Systems | After saving test, Code Expert causes an exception error when closing. | 9/17/2024 |
| R-37895 | TP 1 | System | Error accessing memory-mapped file message received when opening hole geometry. | 9/17/2024 |
| R-37933 | TP 1 | System | Files in the machine group properties should be added to the content file if they do not reside in the Mill-Turn machine environment. | 9/17/2024 |
| R-33456 | TP 1 | CAD | Mastercam 2023 bringing in MBD annotations incorrectly from a SOLIDWORKS file. | 9/17/2024 |
| R-37629 | TP 1 | Milling Toolpaths | Custom slitting saw is not cutting the stock model correctly. | 9/17/2024 |
| R-37848 | TP 1 | Milling Toolpaths | Deburr 3-Axis geometry colors do not display. | 9/17/2024 |
| R-37299 | TP 1 | Milling Toolpaths | In Deburr, switching from a tapered endmill to a lollipop throws a Contact Point Profile Segment error. | 9/17/2024 |
| R-37380 | TP 1 | Milling Toolpaths | In Contour 2D, the incremental retract behaves strangely. | 9/17/2024 |
| R-36876 | TP 1 | Toolpath Utilities | Import Operation imports all operations instead of an individually selected Operation. | 9/17/2024 |
| R-37917 | TP 1 | Backplot/Verify/Simulation | In Mill-Turn simulation, when defining a tool as a counterbore, the holder and cutter are shown floating in space. | 9/17/2024 |
| R-38169 | TP 1 | Milling Toolpaths | Multiaxis Swarf Machining - Rotation of a tool does not affect Climb/Conventional Setting | 9/17/2024 |
| R-37635 | TP 1 | Backplot/Verify/Simulation | Simulated Wire 4-axis toolpath seems to change the toolpath for additional skim cuts. | 9/17/2024 |
| R-36882 | TP 1 | Backplot/Verify/Simulation | A part causes a crash when verifying. | 9/17/2024 |
| R-35930 | TP 1 | Backplot/Verify/Simulation | In Verify, the rapid cycle time is incorrect. | 9/17/2024 |
| R-37388 | TP 1 | Machine Systems | In DMG Mori NTX machine simulation, the tool crashes into the part. | 9/17/2024 |
| R-38404 | TP 1 | Milling Toolpaths | Drill linking parameters change from absolute to incremental. | 9/17/2024 |
| R-36922 | TP 1 | Milling Toolpaths | The Drill reference retract point is incorrect with clearance at all locations. | 9/17/2024 |
| R-38433 | TP 1 | Milling Toolpaths | Creating a drill subprogram that references another drill subprogram does not work. | 9/17/2024 |
| R-36099 | TP 1 | Backplot/Verify/Simulation | In Verify, add the machining time for each toolpath. | 9/17/2024 |
| R-32931 | TP 1 | Milling Toolpaths | Create a tool button within the Tool section of the toolpath parameters dialog box. | 9/17/2024 |
| R-38959 | TP 1 | Tooling | Face mill GTC imports with a chamfer instead of the tool's radius. | 9/17/2024 |
| R-37437 | TP 1 | Backplot/Verify/Simulation | Face threading does not show true threads in Mill-Turn simulation but works in Verify. | 9/17/2024 |
| R-37353 | TP 1 | Machine Systems | Getting a non-cutting representation of a boring bar is failing. | 9/17/2024 |
| R-38153 | TP 1 | Milling Toolpaths | For graphical planes, Mill planes are incorrect with open solid chain and WCS. | 9/17/2024 |
| R-39015 | TP 1 | Tooling | When importing, GTC flat endmill has an oversized edge break. | 9/17/2024 |
| R-36518 | TP 1 | Milling Toolpaths | With the Helix Bore toolpath, the G41/G42 wear compensation codes are not output to the NCI in certain cases. | 9/17/2024 |
| R-37436 | TP 1 | Milling Toolpaths | On the Multiaxis Deburr Holder page, projection edits do no mark the toolpath dirty. | 9/17/2024 |
| R-37007 | TP 1 | Milling Toolpaths | In hole making, axis substitution is not working properly with Advanced Drill in Mill or Mill-Turn. | 9/17/2024 |
| R-37474 | TP 1 | Toolpath Utilities | Importing multiple operations with common tool and WCS planes is spawning an error message. | 9/17/2024 |
| R-37346 | TP 1 | Toolpath Utilities | Importing operations with geometry does not import geometry in the destination file's construction plane. | 9/17/2024 |
| R-37630 | TP 1 | Machine Systems | IOF sub-operations cause unwanted C-axis output in the posted program. | 9/17/2024 |
| R-39417 | TP 1 | System | There are BNCI data loss issues with this 9 GB part file. | 9/17/2024 |
| R-38261 | TP 1 | Turning Toolpaths | When using stock flip, Lathe Thread shows as the opposite hand in Verify. | 9/17/2024 |
| R-36657 | TP 1 | Toolpath Utilities | With Lathe Toolpath Editor, when adding more than one point to a toolpath, only the first point persists. | 9/17/2024 |
| R-34777 | TP 1 | System | Remove Mastercam Art. | 9/17/2024 |
| R-38551 | TP 1 | Tooling | Mastercam crashes when opening a file that 2023 opens successfully. | 9/17/2024 |
| R-35214 | TP 1 | Milling Toolpaths | Mastercam hangs and becomes sluggish with large files and multiaxis toolpaths. | 9/17/2024 |
| R-39156 | TP 1 | Milling Toolpaths | Mastercam is slow to open the Toolpath Control tab from the parameters page. | 9/17/2024 |
| R-38215 | TP 1 | Toolpath Utilities | Reduce duplicate planes in import and export operations. | 9/17/2024 |
| R-38465 | TP 1 | Milling Toolpaths | Mastercam parts created before Mastercam 2024 and opened in Mastercam 2024 or later show fixtures as the workpiece. | 9/17/2024 |
| R-38915 | TP 1 | Milling Toolpaths | In machine group setup, validation for sequence numbers on the Machine +page causes a problem. | 9/17/2024 |
| R-38034 | TP 1 | Backplot/Verify/Simulation | Sub-spindle stock is not displayed in Mill-Turn simulation. | 9/17/2024 |
| R-37061 | TP 1 | Milling Toolpaths | 3-axis Deburr is using the wrong coordinate system for user-defined clearance plane calculation. | 9/17/2024 |
| R-37710 | TP 1 | Backplot/Verify/Simulation | In Mill-Turn simulation, you get an error when using Tool Call in the turret. | 9/17/2024 |
| R-38007 | TP 1 | Machine Systems | In Sync Manager, the retract reference position is set to none, instead of the default reference position. | 9/17/2024 |
| R-38200 | TP 1 | Tooling | The Mill Generic Tool Catalog (GTC) importer is not using the usable length as the shoulder length. | 9/17/2024 |
| R-39078 | TP 1 | Milling Toolpaths | Entries on the Tool page of the Mill toolpath dialog are not saved. | 9/17/2024 |
| R-38055 | TP 1 | Backplot/Verify/Simulation | Mill-Turn simulation causes an Invalid number of axes error when processing data for the turret park operation with Tool Call selected. | 9/17/2024 |
| R-39139 | TP 1 | Milling Toolpaths | Misc values is getting set in the NCI only for first hole in a 5-axis drill toolpath. | 9/17/2024 |
| R-37723 | TP 1 | CAD | Model Prep gives a Face Check Fails warning when attempting to Push-Pull 0 or D . | 9/17/2024 |
| R-37741 | TP 1 | Turning Toolpaths | Mill-Turn A-axis simulation gouges as the tool passes 360. | 9/17/2024 |
| R-38657 | TP 1 | Backplot/Verify/Simulation | In Mill-Turn simulation, holders are mounted inside the milling head after adjusting projection. | 9/17/2024 |
| R-38223 | TP 1 | Milling Toolpaths | Mill-Turn simulation causes an unknown error. | 9/17/2024 |
| R-37305 | TP 1 | Backplot/Verify/Simulation | Mill-Turn simulation causes unexpected error. | 9/17/2024 |
| R-38855 | TP 1 | Milling Toolpaths | Multiaxis operations not going dirty after editing them a second time. | 9/17/2024 |
| R-32289 | TP 1 | Milling Toolpaths | The Rotary Advanced toolpath has one final pass that cuts progressively deeper as it gets closer to the center of the part leaving a false cut/gouge. | 9/17/2024 |
| R-35842 | TP 1 | Milling Toolpaths | In 5-axis Deburr, a 2023 file crashes in 2024 when regenerated. | 9/17/2024 |
| R-36649 | TP 1 | Milling Toolpaths | Multiaxis Deburr (3+2) creates unexpected moves in 2024/2025. | 9/17/2024 |
| R-37598 | TP 1 | Milling Toolpaths | A Unified curve error message needs rewording. | 9/17/2024 |
| R-36201 | TP 1 | Milling Toolpaths | The Unified line lead-in is ignored in 2024 and 2025. | 9/17/2024 |
| R-38636 | TP 1 | Milling Toolpaths | The Unified toolpath shows the wrong chaining dialog for selecting curves. | 9/17/2024 |
| R-33039 | TP 1 | Milling Toolpaths | In Unified, Follow surfaces linking violates the drive surface. | 9/17/2024 |
| R-34995 | TP 1 | Milling Toolpaths | The Swarf toolpath start position changes in Mastercam 2024. | 9/17/2024 |
| R-37146 | TP 1 | Milling Toolpaths | The operation Work Offset number is not updated in Toolpaths Manager. | 9/17/2024 |
| R-38849 | TP 1 | Milling Toolpaths | In Optirough, microlift height causes a gouging link move. | 9/17/2024 |
| R-37180 | TP 1 | Tooling | Validation does not work for the countersink tool. | 9/17/2024 |
| R-34660 | TP 1 | CAD | Parasolid errors occur in a Mastercam 2023 part file with a toolpath. | 9/17/2024 |
| R-39040 | TP 1 | Milling Toolpaths | The plunge rate is incorrect for the second chain after a change. | 9/17/2024 |
| R-33945 | TP 1 | Milling Toolpaths | Pocketing roughing does not cut around one boss. | 9/17/2024 |
| R-38109 | TP 1 | Milling Toolpaths | In Port Expert, an unknown exception is thrown when utilizing stock. | 9/17/2024 |
| R-39213 | TP 1 | File Management | Certain Mastercam 2024 part files have problems in 2025. | 9/17/2024 |
| R-37626 | TP 1 | Selection/Chaining | Process Hole selections areincomplete in Mastercam 2025. | 9/17/2024 |
| R-37787 | TP 1 | Toolpath Utilities | In ProDrill, helix bore Start at center/End at center does not select End at center in the operation. | 9/17/2024 |
| R-37898 | TP 1 | Toolpath Utilities | In ProDrill, Maximum length difference to group as one form does not appear to function properly. | 9/17/2024 |
| R-37138 | TP 1 | Milling Toolpaths | In Engraving, the toolpath leaves stock around the outside edges. | 9/17/2024 |
| R-37253 | TP 1 | Milling Toolpaths | The Saw toolpath does not apply the compensation direction correctly when the spindle is counter-clockwise (CCW). | 9/17/2024 |
| R-37252 | TP 1 | Milling Toolpaths | The Saw toolpath plunges after last clearance move. | 9/17/2024 |
| R-09666 | TP 1 | Selection/Chaining | Add freehand support to selection. | 9/17/2024 |
| R-38982 | TP 1 | Selection/Chaining | Rework how the solid arc edge center point is selected. | 9/17/2024 |
| R-38837 | TP 1 | CAD | When in Dynamic Transform and Translate, if you use the Autocursor Point function, you can still select screen positions and not just Points. | 9/17/2024 |
| R-38387 | TP 1 | Milling Toolpaths | Stock Model operation has a false cut in. | 9/17/2024 |
| R-37736 | TP 1 | Milling Toolpaths | The Stock Model result is incorrect or incomplete when Mill flutes only is checked. | 9/17/2024 |
| R-31006 | TP 1 | Milling Toolpaths | Stock Model creates a stock model from a result of a merge pattern. | 9/17/2024 |
| R-36329 | TP 1 | Milling Toolpaths | The Stock Model still displays when the operation is dirty and can not be removed if the operation is deleted. | 9/17/2024 |
| R-37692 | TP 1 | Machine Systems | The Stock origin/anchor point parameter 19212 does not update. | 9/17/2024 |
| R-23336 | TP 1 | Milling Toolpaths | Waterline Add cuts does not work as expected. | 9/17/2024 |
| R-32518 | TP 1 | Milling Toolpaths | Swarf Milling, Number of layers doesn't seem to have an effect. | 9/17/2024 |
| R-39258 | TP 1 | System | A 9 GB part file has performance issues. | 9/17/2024 |
| R-37863 | TP 1 | General | Add the Deburr 3-axis toolpath to the gallery for Lathe with a Mill or Router license. | 9/17/2024 |
| R-31334 | TP 1 | Milling Toolpaths | There is an incorrect extra move in the Unified toolpath after a Helix Bore/Thread Mill operation. | 9/17/2024 |
| R-37815 | TP 1 | Milling Toolpaths | Display graphical elements still displays after the toolpath is closed or deleted. | 9/17/2024 |
| R-38920 | TP 1 | Milling Toolpaths | In Facing, a feed-rate change applies only to the first chain in a multiple-chain case. | 9/17/2024 |
| R-37922 | TP 1 | Milling Toolpaths | In Drill, voids are seen as a single hole for solid bodies with coaxial holes. | 9/17/2024 |
| R-38958 | TP 1 | Milling Toolpaths | Toolpath regeneration is required in Mastercam 2025 after editing feeds and speeds in tool or operation. | 9/17/2024 |
| R-22935 | TP 1 | Milling Toolpaths | The Pocket toolpath is missing cuts. | 9/17/2024 |
| R-37263 | TP 1 | General | The Productivity+ machine update cycle throws errors if the planes have Korean characters. | 9/17/2024 |
| R-38724 | TP 1 | Backplot/Verify/Simulation | In toolpath display, the tool contact point shows unexpected connecting lines and wrong transformations. | 9/17/2024 |
| R-39006 | TP 1 | Backplot/Verify/Simulation | A thread on the sub-spindle verifies the opposite of the workpiece. | 9/17/2024 |
| R-31488 | TP 1 | Backplot/Verify/Simulation | In Advanced Drill, Verify and Stock Model push the tool radius too deep. | 9/17/2024 |
| R-37722 | TP 1 | Backplot/Verify/Simulation | Lathe custom thread not simulating correctly | 9/17/2024 |
| R-37590 | TP 1 | Backplot/Verify/Simulation | Problem with Toolpath Transform. | 9/17/2024 |
| R-38961 | TP 1 | Milling Toolpaths | In Unified, the Apply button does not update the toolpath. | 9/17/2024 |
| R-39327 | TP 1 | Milling Toolpaths | In Unified, the Use negative side tilt checkbox on the Tool Axis Control page does not retain its state. | 9/17/2024 |
| R-37400 | TP 1 | Milling Toolpaths | Unified, the Perform spiral drop-down resets to Full when Blend along distance is selected. | 9/17/2024 |
| R-38898 | TP 1 | Tooling | A tool image shows an unreadable font. | 9/17/2024 |
| R-36717 | TP 1 | Wire | A Wire EDM model violation is not shown as collision. | 9/17/2024 |
| R-37325 | TP 1 | Backplot/Verify/Simulation | Verify and Machine Simulation rotation angles are calculated incorrectly for a part. | 9/17/2024 |
| R-36161 | TP 1 | Milling Toolpaths | Verify crashes immediately in Mastercam 2024 using Mill-Turn. | 9/17/2024 |
| R-32239 | TP 1 | Backplot/Verify/Simulation | A Lathe operation in a machine that was loaded after a Mill-Turn machine crashes Mastercam. | 9/17/2024 |
| R-38511 | TP 1 | Wire | In Wire, clicking Apply resets the skim cuts and half of the pages. | 9/17/2024 |
| R-36654 | TP 1 | CAD | Add a new configuration/CAD setting to enable or disable the drag selection for Wireframe Fillet, Chamfer, Dynamic Trim, Trim to Entities, and Divide. | 9/17/2024 |
| R-36893 | TP 1 | CAD | Add ability to read in Mark Command features from Autodesk Inventor into Mastercam. | 9/17/2024 |
| R-33725 | TP 1 | CAD | When opening the latest version of Alibre Design .AD_PRT models you get an error in Mastercam 2023. | 9/17/2024 |
| R-36011 | TP 1 | CAD | A Step file exported from Catia does not show bend line information in Mastercam 2024. | 9/17/2024 |
| D-54288 | TP 1 | Machine Systems | An axis toolpath icon is missing in Sync Manager. | 9/17/2024 |
| R-37569 | TP 1 | CAD | Analyze entity is taking a long time to open when analyzing a model. | 9/17/2024 |
| R-38897 | TP 1 | CAD | Auto orientation does not give minimum bounding box. | 9/17/2024 |
| R-35094 | TP 1 | CAD | With the IGS converter, arcs are converted to splines upon import. | 9/17/2024 |
| R-29502 | TP 1 | CAD | The IGES converter imports B-Rep solids (IGES type 510) as surfaces incorrectly. | 9/17/2024 |
| R-37623 | TP 1 | CAD | A SOLIDWORKS part file has split faces in SOLIDWORKS but the splits are lost when imported into Mastercam. | 9/17/2024 |
| R-36883 | TP 1 | CAD | Add a message in the lower left of the blue status bar that displays the progress of entities getting deleted. | 9/17/2024 |
| R-38206 | TP 1 | CAD | In Drafting, keep associativity to a line after trimming it with the divide command. | 9/17/2024 |
| R-38421 | TP 1 | CAD | In Drafting (Circular) Dimension Attributes, the Diameter symbol is incorrect. | 9/17/2024 |
| R-37298 | TP 1 | CAD | DWG/DXF files read into Mastercam with lines not connected to arc properly. | 9/17/2024 |
| R-38158 | TP 1 | CAD | DWG/DXF files read into Mastercam with lines not connected to arc properly. | 9/17/2024 |
| R-36789 | TP 1 | CAD | DWG/DXF files read into Mastercam with lines not connected to arc properly. | 9/17/2024 |
| R-38943 | TP 1 | CAD | Saving file from Mastercam 2023 throws an error and generates a psxc file. | 9/17/2024 |
| R-39044 | TP 1 | CAD | A Parasolid error occurs when you open the Mastercam part file. | 9/17/2024 |
| R-37779 | TP 1 | CAD | Fixed issue causing assert when double-clicking a toolpath operation with solid geometry. | 9/17/2024 |
| R-39098 | TP 1 | CAD | Writing out 3D PDF files with solids causes an error. | 9/17/2024 |
| R-34121 | TP 1 | CAD | Importing IGES an assembly file aligns several components wrong. | 9/17/2024 |
| R-34821 | TP 1 | CAD | Importing an IGES file from Mechanical Desktop is not working. | 9/17/2024 |
| R-37765 | TP 1 | CAD | An Inventor file is losing the 3D Annotation. | 9/17/2024 |
| R-38213 | TP 1 | CAD | Model Prep crashes when you click OK in the Remove Fillets panel. | 9/17/2024 |
| R-38438 | TP 1 | CAD | A Nesting operation causes Mastercam to crash. | 9/17/2024 |
| R-38590 | TP 1 | CAD | Meshes from Entities does not delete trimmed or untrimmed surfaces. | 9/17/2024 |
| R-37881 | TP 1 | CAD | Mirroring horizontal ordinate dimensions makes them incorrect. | 9/17/2024 |
| R-38436 | TP 1 | CAD | Make Push-Pull checkmarks behave like Move. | 9/17/2024 |
| R-37303 | TP 1 | CAD | Model Prep Disassemble does not preview when you manually enter a location into the Start Point field. | 9/17/2024 |
| R-37284 | TP 1 | CAD | Model Prep was not copying as expected when the Entity type was set to copy. | 9/17/2024 |
| R-35948 | TP 1 | CAD | When opening a dwg file in Mastercam 2024, the part comes in as splines instead of lines. | 9/17/2024 |
| R-35571 | TP 1 | CAD | DWG creates lines in Mastercam 2023 and splines in 2024. | 9/17/2024 |
| R-35222 | TP 1 | CAD | DXF converter converts lines to splines upon import. | 9/17/2024 |
| R-37649 | TP 1 | CAD | NX file is not opening in Mastercam. | 9/17/2024 |
| R-36460 | TP 1 | CAD | Sketches are missing when a SLDPRT file is imported. | 9/17/2024 |
| R-38910 | TP 1 | CAD | Solids get corrupted when you press Apply for Model Prep, Remove Fillet. | 9/17/2024 |
| R-37583 | TP 1 | CAD | In Solids (Block), you are not able to enter coordinates after changing the base point. | 9/17/2024 |
| R-21975 | TP 1 | CAD | Some bad trimmed surfaces are created when you import IGES files fixed for Mastercam 2026. | 9/17/2024 |
| R-36476 | TP 1 | CAD | Some corner Fillets not coming into Mastercam from a Creo 2024 file. | 9/17/2024 |
| R-37026 | TP 1 | CAD | Surface draft dimensions are not modal during a Mastercam session. | 9/17/2024 |
| R-38945 | TP 1 | CAD | The Solid body name is renamed to Solid when moved with any transform function. | 9/17/2024 |
| R-38944 | TP 1 | CAD | The Solid body name is renamed to Solid when moved with any transform function. | 9/17/2024 |
| R-38916 | TP 1 | CAD | In toolpath nesting, Nest to Tool center or Nest to Tool Diameter does not stay selected. | 9/17/2024 |
| R-38894 | TP 1 | CAD | In toolpath nesting, Nest to Tool center or Nest to Tool Diameter does not stay selected. | 9/17/2024 |
| R-38789 | TP 1 | CAD | In toolpath nesting from a file, the plunge and retract rate gets pulled for the tool library and not the toolpath parameters. | 9/17/2024 |
| R-38957 | TP 1 | CAD | In Transform (Geometry Nesting), Place label on top of solid is not working. | 9/17/2024 |
| R-37576 | TP 1 | CAD | In Transform Offset Chains, allow panel values to be adjusted prior to chaining. | 9/17/2024 |
| R-36252 | TP 1 | CAD | Set the solid-edge selection in the AutoCursor selection bar to modal. | 9/17/2024 |
| R-38019 | TP 1 | CAD | Creating an angular dimension and setting Angular to Deg/Min/Sec changes Format from Decimal to Scientific. | 9/17/2024 |
| R-37241 | TP 1 | CAD | When importing an IPT file into Mastercam, the Colors were not imported as expected. | 9/17/2024 |
| R-38692 | TP 1 | CAD | When using Disassemble, changing Placement to Manual, clicking the blue check, and then setting Placement back to Automatic, you lose the ability to window select the solids in the workspace. | 9/17/2024 |
| R-37854 | TP 1 | CAD | When using Line Parallel and locking or unlocking the Offset Distance after selecting a line will give unexpected behavior. | 9/17/2024 |
| R-38970 | TP 1 | CAD | Wireframe - Turn Profile-Slice crashes Mastercam. | 9/17/2024 |
| R-38981 | TP 1 | CAD | Wireframe - Turn Profile-Slice crashes Mastercam. | 9/17/2024 |
| R-38977 | TP 1 | CAD | Wireframe point segment, when multiple chains are selected points end up off of the selected chains. | 9/17/2024 |
| R-37092 | TP 1 | CAD | Writing Step files out of Mastercam will now save the custom planes. When you open the STEP file those planes will be there. | 9/17/2024 |
| R-38769 | TP 1 | CAD | In Transform (Translate), moved geometry is not updated in the preview. | 9/17/2024 |
Quick Links
Knowledge Base
Find useful tips and tricks and discover information about common work-arounds.
Downloads
Download current and previous versions of Mastercam products, add-ons, and utilities.
Mastercam University
24/7 online training for anyone looking to begin a career in CNC programing.
