Canon esp bowtie.xml

Page auto-generated from XML file.

---

Failure

The generated TethysL source could not be parsed, likely due to source XML not being well-formed.

Below is the compile error at the TethysL level, as well as the source XML.

The TethysL file name shown below does not necessarily indicate the file exists, but hints about the actual corresponding .xml file.

Syntax error:
    --> lrauv-application/Missions/Deprecated/Science/canon_esp_bowtie.xml:468:7
     | 
 464 | 
 465 | 
 466 |       # Configure sampling sequance
 467 | 
 468 |       assign in sequence Sample:SampleCANONSampler = SampleCANONSampler
     |       ^^^^^^
 469 | 
 470 |       assign in sequence Sample:CANONSamplerDelay = CANONSamplerDelay
 471 | 
 472 |       assign in sequence Sample:ESPCartridgeType = CartridgeType
     | 
Unexpected: `assign`
Expecting: 'unit' <<<<

Generated TethysL

mission canon_esp_bowtie {
  """
  This mission cycles through the CANON Bowtie waypoints in the order: SE
  - NW - NE - SW - SE and sets the max depth for each leg. The mission can
  (re)start at any point within this trajectory by adjusting the `leg`
  parameter as needed.
  """

  arguments {
    # Almost every mission should start with an overall timeout and a NeedCommsTime.

    MissionTimeout = 14 hour
      """
      Maximum duration of mission
      """

    NeedCommsTime = 120 minute
      """
      How often to surface for commumications
      """

    # You probably need to change these.

    leg = 1 count
      """
      Leg to start at (default is start at leg 1). leg 1: SE (to start
      position) leg 2: SE - CSE leg 3: CSE - CNW leg 4: CNW - NW leg 5: NW - N
      leg 6: N - NE leg 7: NE - CNE leg 8: CNE - CSW leg 9: CSW - SW leg 10:
      SW - S leg 11: S - SE leg 12: SE - ? (spare wp)
      """

    SampleInterval = 2 hour
      """
      ESP sampling interval. Must be longer than the duration of a single ESP
      sample.
      """

    SampleInterval = 2 hour
      """
      ESP sampling interval. Must be longer than the duration of a single ESP
      sample.
      """

    SampleESP = true
      """
      When true, aqurie an ESP sample.
      """

    CartridgeType = -6 count
      """
      Specifies ESP cartridge type code (defaults to archive_bac: -6)
      """

    SampleCANONSampler = false
      """
      When true, aqurie a CANON Sampler water sample.
      """

    CANONSamplerDelay = 10 minute
      """
      How long to delay a CANON Sampler sample after an ESP sample is
      intiated.
      """

    SampleTimeout = 3 hour
      """
      Max time duration allowed for a single sample.
      """

    StartWithASample = true
      """
      When true, the mission will acquire and ESP sample at the start of the
      mission. When false, the mission will wait for the SampleInterval before
      acquiring the first sample.
      """

    Lat1 = 36.7755 degree
      """
      Latitude of waypoint 1 (default: SE).
      """

    Lon1 = -121.825 degree
      """
      Longitude of waypoint 1 (default: SE).
      """

    Lat2 = 36.787825 degree
      """
      Latitude of waypoint 2 (default: CSE).
      """

    Lon2 = -121.841121 degree
      """
      Longitude of waypoint 2 (default: CSE).
      """

    Lat3 = 36.804417 degree
      """
      Latitude of waypoint 3 (default: CNW).
      """

    Lon3 = -121.862712 degree
      """
      Longitude of waypoint 3 (default: CNW).
      """

    Lat4 = 36.8219 degree
      """
      Latitude of waypoint 4 (default: NW).
      """

    Lon4 = -121.8856 degree
      """
      Longitude of waypoint 4 (default: NW).
      """

    Lat5 = 36.829608 degree
      """
      Latitude of waypoint 5 (default: N).
      """

    Lon5 = -121.853778 degree
      """
      Longitude of waypoint 5 (default: N).
      """

    Lat6 = 36.8315 degree
      """
      Latitude of waypoint 6 (default: NE).
      """

    Lon6 = -121.8457 degree
      """
      Longitude of waypoint 6 (default: NE).
      """

    Lat7 = 36.812109 degree
      """
      Latitude of waypoint 7 (default: CNE).
      """

    Lon7 = -121.851505 degree
      """
      Longitude of waypoint 7 (default: CNE).
      """

    Lat8 = 36.785431 degree
      """
      Latitude of waypoint 8 (default: CSW).
      """

    Lon8 = -121.859331 degree
      """
      Longitude of waypoint 8 (default: CSW).
      """

    Lat9 = 36.766 degree
      """
      Latitude of waypoint 9 (default: SW).
      """

    Lon9 = -121.8649 degree
      """
      Longitude of waypoint 9 (default: SW).
      """

    Lat10 = 36.769648 degree
      """
      Latitude of waypoint 10 (default: S).
      """

    Lon10 = -121.848834 degree
      """
      Longitude of waypoint 10 (default: S).
      """

    Lat11 = 36.7755 degree
      """
      Latitude of waypoint 11 (default: SE).
      """

    Lon11 = -121.825 degree
      """
      Longitude of waypoint 11 (default: SE).
      """

    Lat12 = NaN degree
      """
      Latitude of waypoint 12 (spare).
      """

    Lon12 = NaN degree
      """
      Longitude of waypoint 12 (spare).
      """

    Speed = 1 meter_per_second
      """
      Vehicle speed for the entire mission.
      """

    YoYoMinDepth = 5 meter
      """
      Minimum YoYo depth for the entire mission.
      """

    YoYoMaxDepth1 = 20 meter
      """
      Maximum YoYo depth during leg 1.
      """

    YoYoMaxDepth2 = 25 meter
      """
      Maximum YoYo depth during leg 2.
      """

    YoYoMaxDepth3 = 100 meter
      """
      Maximum YoYo depth during leg 3.
      """

    YoYoMaxDepth4 = 70 meter
      """
      Maximum YoYo depth during leg 4.
      """

    YoYoMaxDepth5 = 65 meter
      """
      Maximum YoYo depth during leg 5.
      """

    YoYoMaxDepth6 = 45 meter
      """
      Maximum YoYo depth during leg 6.
      """

    YoYoMaxDepth7 = 45 meter
      """
      Maximum YoYo depth during leg 7.
      """

    YoYoMaxDepth8 = 100 meter
      """
      Maximum YoYo depth during leg 8.
      """

    YoYoMaxDepth9 = 65 meter
      """
      Maximum YoYo depth during leg 9.
      """

    YoYoMaxDepth10 = 50 meter
      """
      Maximum YoYo depth during leg 10.
      """

    YoYoMaxDepth11 = 20 meter
      """
      Maximum YoYo depth during leg 11.
      """

    YoYoMaxDepth12 = 20 meter
      """
      Maximum YoYo depth during leg 12.
      """

    YoYoMinAltitude = 9 meter
      """
      Minimum altitude while performing the YoYo behavior (for
      bottom-terminated YoYos).
      """

    YoYoUpPitch = 20 degree
      """
      Vehicle up pitch while performing the YoYo behavior.
      """

    YoYoDownPitch = -20 degree
      """
      Vehicle down pitch while performing the YoYo behavior.
      """

    # You are even less likely to need to change these.

    CaptureRadius = NaN meter
      """
      Waypoint capture radiues.
      """

    MinAltitude = 5 meter
      """
      Minimum height above the sea floor for the entire mission.
      """

    MaxDepth = 110 meter
      """
      Maximum depth for the entire mission.
      """

    MinOffshore = 2 kilometer
      """
      Minimum offshore distance for the entire mission.
      """
  }

  output {
    ElapsedSinceLastSampleStart = 0 minute
      """
      Mission variable (don't change). The mission sets this variable to reset
      the ESP sample timer.
      """

    ElapsedTime = 0 hour
      """
      Mission variable (don't change). The mission sets this variable to reset
      the ESP sample timer.
      """

    SampleInProgress = false
      """
      Mission variable (don't change). The mission sets this variable to while
      sampling is in progress.
      """
  }

  # Missions should almost always start with a timeout

  timeout duration=MissionTimeout

  insert Insert/Science.xml {
    """
    Most missions will run the science sensors. If you don't place this
    aggregate above NeedComms, science instruments get turned off on the
    last upcast and while floating on the surface.
    """
  }



  # Most missions should use the NeedComms aggregate.

  insert Insert/NeedComms.xml id="NeedComms"


  assign in sequence NeedComms:DiveInterval = NeedCommsTime

  # Missions should almost always start with standard safety envelopes;
  #                  most missions should not expose the parameters of these envelopes.

  insert Insert/StandardEnvelopes.xml


  assign in sequence StandardEnvelopes:MinAltitude = MinAltitude

  assign in sequence StandardEnvelopes:MaxDepth = MaxDepth

  assign in sequence StandardEnvelopes:MinOffshore = MinOffshore

  assign in sequence StandardEnvelopes:MaxDepth = MaxDepth

  assign in sequence StandardEnvelopes:MinOffshore = MinOffshore

  # Sampling directives

  aggregate CheckSamplingSettings {
    run in sequence

    syslog info "Checking sampling settings."

    aggregate CheckESP {
      run when (
        SampleESP
        and ( not ( Science:ESPComponent.loadAtStartup ) )
      )

      syslog critical "Cannot service ESP sample request. ESPComponent is not loaded."
    }

    aggregate CheckCANONSampler {
      run when (
        SampleCANONSampler
        and ( not ( Science:CANONSampler.loadAtStartup ) )
      )

      syslog critical "Cannot service CANONSampler water sample request. CANONSampler component is not loaded."
    }
  }

  insert Insert/Sample.xml {
    redefineArg SampleTimeout = SampleTimeout
  }



  # Automatically cycle logs every 24 hours

  aggregate CycleLogs {
    run in parallel

    aggregate {
      run in sequence

      behavior Guidance:Wait {
        run in sequence
        set Guidance:Wait.duration = 24 hour
      }

      syslog important "Restarting logs."

      behavior Guidance:Execute {
        run in sequence
        set Guidance:Execute.command = "restart logs"
      }
    }
  }

  # Acquire ESP sample every SampleInterval

  aggregate SampleTimer {
    run while (
      SampleInProgress
      or ( elapsed ( ElapsedSinceLastSampleStart ) > SampleInterval )
    )

    aggregate AcquireSample {
      run in sequence

      assign in sequence ElapsedTime = elapsed ( ElapsedSinceLastSampleStart )

      syslog important "Pre-sample comms. Elapsed time since last ESP sample: "
           + ElapsedTime ~ hour

      # Surface for comms before initiating the sample sequence

      call id="PreSampleComms" refId="NeedComms"

      # Set the surface comms interval to the sample timeout to avoid interruptions while sampling

      assign in sequence NeedComms:DiveInterval = SampleTimeout

      aggregate WaitForDepth {
        run in sequence

        break if (
          Universal:depth >= YoYoMinDepth
        )

        syslog info "Waiting to achieve min depth of "
             + YoYoMinDepth ~ meter

        behavior Guidance:Wait {
          run in sequence
          set Guidance:Wait.duration = SampleTimeout
        }
      }

      # Indicate a sample is in progress

      assign in sequence SampleInProgress = true

      # This assignment restarts the sample timer

      assign in sequence ElapsedSinceLastSampleStart = 0 #<No-Units?>


      # Configure sampling sequance

      assign in sequence Sample:SampleCANONSampler = SampleCANONSampler

      assign in sequence Sample:CANONSamplerDelay = CANONSamplerDelay

      assign in sequence Sample:ESPCartridgeType = CartridgeType

      assign in sequence Sample:SampleESP = SampleESP

      # Trigger sampling sequance

      call id="TriggerSample" refId="Sample"

      # Surface for comms after the sampling sequence completes

      call id="PreSampleComms" refId="NeedComms"

      # Reinstate nominal surface comms interval

      assign in sequence NeedComms:DiveInterval = NeedCommsTime

      assign in sequence SampleInProgress = false
    }
  }

  call id="StartingMission" refId="NeedComms"

  # Many missions will keep mass position and buoyancy volume fixed at defaults.

  behavior Guidance:Pitch {
    run in parallel
    set Guidance:Pitch.massPosition = Control:VerticalControl.massDefault
  }

  behavior Guidance:Buoyancy {
    run in parallel
    set Guidance:Buoyancy.position = Control:VerticalControl.buoyancyNeutral
  }

  behavior Guidance:SetSpeed {
    run in parallel
    set Guidance:SetSpeed.speed = Speed
  }

  behavior Guidance:DepthEnvelope {
    """
    Another depth envelope for the YoYo behavior. This envelope should
    fall within the limits of the standard safety envelopes in
    Insert/StandardEnvelopes.xml in order to avoid commanding high pitch
    angles for depth-terminated YoYos.
    """
    run in parallel
    set Guidance:DepthEnvelope.minDepth = YoYoMinDepth
    set Guidance:DepthEnvelope.downPitch = YoYoDownPitch
    set Guidance:DepthEnvelope.upPitch = YoYoUpPitch
  }

  behavior Guidance:AltitudeEnvelope {
    """
    Another altitude envelope for the YoYo behavior. This envelope
    should fall within the limits of the standard safety envelopes in
    Insert/StandardEnvelopes.xml in order to avoid commanding high pitch
    angles for bottom-terminated YoYos.
    """
    run in parallel
    set Guidance:AltitudeEnvelope.minAltitude = YoYoMinAltitude
    set Guidance:AltitudeEnvelope.upPitch = YoYoUpPitch
  }

  behavior Guidance:YoYo {
    run in parallel
    set Guidance:YoYo.downPitch = YoYoDownPitch
    set Guidance:YoYo.upPitch = YoYoUpPitch
  }

  aggregate SetWaypointsPerLegParameter {
    """
    The following Leg2-5 aggregates adjust the Lat[] and Lon[] variables
    according to the `trajectory` parameter:
    """

    run in sequence

    aggregate Leg2 {
      run in sequence

      break if (
        leg <= 1 count
      )

      assign in sequence Lat1 = NaN degree

      assign in sequence Lon1 = NaN degree
    }

    aggregate Leg3 {
      run in sequence

      break if (
        leg <= 2 count
      )

      assign in sequence Lat2 = NaN degree

      assign in sequence Lon2 = NaN degree
    }

    aggregate Leg4 {
      run in sequence

      break if (
        leg <= 3 count
      )

      assign in sequence Lat3 = NaN degree

      assign in sequence Lon3 = NaN degree
    }

    aggregate Leg5 {
      run in sequence

      break if (
        leg <= 4 count
      )

      assign in sequence Lat4 = NaN degree

      assign in sequence Lon4 = NaN degree
    }

    aggregate Leg6 {
      run in sequence

      break if (
        leg <= 5 count
      )

      assign in sequence Lat5 = NaN degree

      assign in sequence Lon5 = NaN degree
    }

    aggregate Leg7 {
      run in sequence

      break if (
        leg <= 6 count
      )

      assign in sequence Lat6 = NaN degree

      assign in sequence Lon6 = NaN degree
    }

    aggregate Leg8 {
      run in sequence

      break if (
        leg <= 7 count
      )

      assign in sequence Lat7 = NaN degree

      assign in sequence Lon7 = NaN degree
    }

    aggregate Leg9 {
      run in sequence

      break if (
        leg <= 8 count
      )

      assign in sequence Lat8 = NaN degree

      assign in sequence Lon8 = NaN degree
    }

    aggregate Leg10 {
      run in sequence

      break if (
        leg <= 9 count
      )

      assign in sequence Lat9 = NaN degree

      assign in sequence Lon9 = NaN degree
    }

    aggregate Leg11 {
      run in sequence

      break if (
        leg <= 10 count
      )

      assign in sequence Lat10 = NaN degree

      assign in sequence Lon10 = NaN degree
    }
  }

  aggregate Lap {
    run in sequence

    syslog important "Starting Lap"

    syslog important "Lat[1] = "
         + Lat1 ~ degree
         + " Lon[1] = "
         + Lon1 ~ degree

    syslog important "Lat[2] = "
         + Lat2 ~ degree
         + " Lon[2] = "
         + Lon2 ~ degree

    syslog important "Lat[3] = "
         + Lat3 ~ degree
         + " Lon[3] = "
         + Lon3 ~ degree

    syslog important "Lat[4] = "
         + Lat4 ~ degree
         + " Lon[4] = "
         + Lon4 ~ degree

    syslog important "Lat[5] = "
         + Lat5 ~ degree
         + " Lon[5] = "
         + Lon5 ~ degree

    syslog important "Lat[6] = "
         + Lat6 ~ degree
         + " Lon[6] = "
         + Lon6 ~ degree

    syslog important "Lat[7] = "
         + Lat7 ~ degree
         + " Lon[7] = "
         + Lon7 ~ degree

    syslog important "Lat[8] = "
         + Lat8 ~ degree
         + " Lon[8] = "
         + Lon8 ~ degree

    syslog important "Lat[9] = "
         + Lat9 ~ degree
         + " Lon[9] = "
         + Lon9 ~ degree

    syslog important "Lat[10] = "
         + Lat10 ~ degree
         + " Lon[10] = "
         + Lon10 ~ degree

    syslog important "Lat[11] = "
         + Lat11 ~ degree
         + " Lon[11] = "
         + Lon11 ~ degree

    syslog important "Lat[12] = "
         + Lat12 ~ degree
         + " Lon[12] = "
         + Lon12 ~ degree

    aggregate SampleOnStart {
      run in sequence

      break if (
        not ( StartWithASample )
      )

      # Kick off the first ESP sample.

      assign in sequence SampleInProgress = true
    }

    # The following aggregates dispatch the waypoints behaviors

    aggregate Wpt1 {
      run in sequence

      syslog important "Navigating to box start WP. YoYoMaxDepth:"
           + YoYoMaxDepth1 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth1
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat1
        set Guidance:Waypoint.longitude = Lon1
      }
    }

    aggregate Wpt2 {
      run in sequence

      syslog important "Navigating to WP2. YoYoMaxDepth: "
           + YoYoMaxDepth2 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth2
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat2
        set Guidance:Waypoint.longitude = Lon2
      }
    }

    aggregate Wpt3 {
      run in sequence

      syslog important "Navigating to WP3. YoYoMaxDepth: "
           + YoYoMaxDepth3 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth3
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat3
        set Guidance:Waypoint.longitude = Lon3
      }
    }

    aggregate Wpt4 {
      run in sequence

      syslog important "Navigating to WP4. YoYoMaxDepth: "
           + YoYoMaxDepth4 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth4
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat4
        set Guidance:Waypoint.longitude = Lon4
      }
    }

    aggregate Wpt5 {
      run in sequence

      syslog important "Navigating to WP5. YoYoMaxDepth:"
           + YoYoMaxDepth5 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth5
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat5
        set Guidance:Waypoint.longitude = Lon5
      }
    }

    aggregate Wpt6 {
      run in sequence

      syslog important "Navigating to WP6. YoYoMaxDepth:"
           + YoYoMaxDepth6 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth6
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat6
        set Guidance:Waypoint.longitude = Lon6
      }
    }

    aggregate Wpt7 {
      run in sequence

      syslog important "Navigating to WP7. YoYoMaxDepth: "
           + YoYoMaxDepth7 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth7
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat7
        set Guidance:Waypoint.longitude = Lon7
      }
    }

    aggregate Wpt8 {
      run in sequence

      syslog important "Navigating to WP8. YoYoMaxDepth: "
           + YoYoMaxDepth8 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth8
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat8
        set Guidance:Waypoint.longitude = Lon8
      }
    }

    aggregate Wpt9 {
      run in sequence

      syslog important "Navigating to WP9. YoYoMaxDepth: "
           + YoYoMaxDepth9 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth9
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat9
        set Guidance:Waypoint.longitude = Lon9
      }
    }

    aggregate Wpt10 {
      run in sequence

      syslog important "Navigating to WP10. YoYoMaxDepth: "
           + YoYoMaxDepth10 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth10
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat10
        set Guidance:Waypoint.longitude = Lon10
      }
    }

    aggregate Wpt11 {
      run in sequence

      syslog important "Navigating to WP11. YoYoMaxDepth: "
           + YoYoMaxDepth11 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth11
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat11
        set Guidance:Waypoint.longitude = Lon11
      }
    }

    aggregate Wpt12 {
      run in sequence

      syslog important "Navigating to WP12. YoYoMaxDepth: "
           + YoYoMaxDepth12 ~ meter

      behavior Guidance:DepthEnvelope {
        set Guidance:DepthEnvelope.maxDepth = YoYoMaxDepth12
      }

      behavior Guidance:Waypoint {
        run in sequence
        set Guidance:Waypoint.latitude = Lat12
        set Guidance:Waypoint.longitude = Lon12
      }
    }
  }
}

Source XML

<?xml version="1.0" encoding="UTF-8"?>
<Mission xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
         xmlns="Tethys"
         xmlns:Units="Tethys/Units"
         xmlns:Control="Tethys/Control"
         xmlns:Guidance="Tethys/Guidance"
         xmlns:Science="Tethys/Science"
         xmlns:Universal="Tethys/Universal"
         xsi:schemaLocation="Tethys http://okeanids.mbari.org/tethys/Xml/Tethys.xsd
                             Tethys/Units http://okeanids.mbari.org/tethys/Xml/Units.xsd
                             Tethys/Control http://okeanids.mbari.org/tethys/Xml/Control.xsd
                             Tethys/Science http://okeanids.mbari.org/tethys/Xml/Science.xsd
                             Tethys/Universal http://okeanids.mbari.org/tethys/Xml/Universal.xsd
                             Tethys/Guidance http://okeanids.mbari.org/tethys/Xml/Guidance.xsd"
       Id="canon_esp_bowtie">

    <Description>
        This mission cycles through the CANON Bowtie waypoints in the order: SE
        - NW - NE - SW - SE and sets the max depth for each leg. The mission can
        (re)start at any point within this trajectory by adjusting the `leg`
        parameter as needed.
    </Description>

<!-- Almost every mission should start with an overall timeout and a NeedCommsTime. -->

    <DefineArg Name="MissionTimeout"><Description>
        Maximum duration of mission
    </Description><Units:hour/><Value>14</Value></DefineArg>

    <DefineArg Name="NeedCommsTime"><Description>
        How often to surface for commumications
    </Description><Units:minute/><Value>120</Value></DefineArg>

<!-- You probably need to change these. -->

    <DefineArg Name="leg"><Description>
        Leg to start at (default is start at leg 1). leg 1: SE (to start
        position) leg 2: SE - CSE leg 3: CSE - CNW leg 4: CNW - NW leg 5: NW - N
        leg 6: N - NE leg 7: NE - CNE leg 8: CNE - CSW leg 9: CSW - SW leg 10:
        SW - S leg 11: S - SE leg 12: SE - ? (spare wp)
    </Description><Units:count/><Value>1</Value></DefineArg>

    <DefineArg Name="SampleInterval"><Description>
        ESP sampling interval. Must be longer than the duration of a single ESP
        sample.
    </Description><Units:hour/><Value>2</Value></DefineArg>

    <DefineArg Name="SampleInterval"><Description>
        ESP sampling interval. Must be longer than the duration of a single ESP
        sample.
    </Description><Units:hour/><Value>2</Value></DefineArg>

    <DefineArg Name="SampleESP"><Description>
        When true, aqurie an ESP sample.
    </Description><True/></DefineArg>

    <DefineArg Name="CartridgeType"><Description>
        Specifies ESP cartridge type code (defaults to archive_bac: -6)
    </Description><Units:count/><Value>-6</Value></DefineArg>

    <DefineArg Name="SampleCANONSampler"><Description>
        When true, aqurie a CANON Sampler water sample.
    </Description><False/></DefineArg>

    <DefineArg Name="CANONSamplerDelay"><Description>
        How long to delay a CANON Sampler sample after an ESP sample is
        intiated.
    </Description><Units:minute/><Value>10</Value></DefineArg>

    <DefineArg Name="SampleTimeout"><Description>
        Max time duration allowed for a single sample.
    </Description><Units:hour/><Value>3</Value></DefineArg>

    <DefineArg Name="StartWithASample"><Description>
        When true, the mission will acquire and ESP sample at the start of the
        mission. When false, the mission will wait for the SampleInterval before
        acquiring the first sample.
    </Description><True/></DefineArg>

    <DefineArg Name="Lat1"><Description>
        Latitude of waypoint 1 (default: SE).
    </Description><Units:degree/><Value>36.7755</Value></DefineArg>

    <DefineArg Name="Lon1"><Description>
        Longitude of waypoint 1 (default: SE).
    </Description><Units:degree/><Value>-121.825</Value></DefineArg>

    <DefineArg Name="Lat2"><Description>
        Latitude of waypoint 2 (default: CSE).
    </Description><Units:degree/><Value>36.787825</Value></DefineArg>

    <DefineArg Name="Lon2"><Description>
        Longitude of waypoint 2 (default: CSE).
    </Description><Units:degree/><Value>-121.841121</Value></DefineArg>

    <DefineArg Name="Lat3"><Description>
        Latitude of waypoint 3 (default: CNW).
    </Description><Units:degree/><Value>36.804417</Value></DefineArg>

    <DefineArg Name="Lon3"><Description>
        Longitude of waypoint 3 (default: CNW).
    </Description><Units:degree/><Value>-121.862712</Value></DefineArg>

    <DefineArg Name="Lat4"><Description>
        Latitude of waypoint 4 (default: NW).
    </Description><Units:degree/><Value>36.8219</Value></DefineArg>

    <DefineArg Name="Lon4"><Description>
        Longitude of waypoint 4 (default: NW).
    </Description><Units:degree/><Value>-121.8856</Value></DefineArg>

    <DefineArg Name="Lat5"><Description>
        Latitude of waypoint 5 (default: N).
    </Description><Units:degree/><Value>36.829608</Value></DefineArg>

    <DefineArg Name="Lon5"><Description>
        Longitude of waypoint 5 (default: N).
    </Description><Units:degree/><Value>-121.853778</Value></DefineArg>

    <DefineArg Name="Lat6"><Description>
        Latitude of waypoint 6 (default: NE).
    </Description><Units:degree/><Value>36.8315</Value></DefineArg>

    <DefineArg Name="Lon6"><Description>
        Longitude of waypoint 6 (default: NE).
    </Description><Units:degree/><Value>-121.8457</Value></DefineArg>

    <DefineArg Name="Lat7"><Description>
        Latitude of waypoint 7 (default: CNE).
    </Description><Units:degree/><Value>36.812109</Value></DefineArg>

    <DefineArg Name="Lon7"><Description>
        Longitude of waypoint 7 (default: CNE).
    </Description><Units:degree/><Value>-121.851505</Value></DefineArg>

    <DefineArg Name="Lat8"><Description>
        Latitude of waypoint 8 (default: CSW).
    </Description><Units:degree/><Value>36.785431</Value></DefineArg>

    <DefineArg Name="Lon8"><Description>
        Longitude of waypoint 8 (default: CSW).
    </Description><Units:degree/><Value>-121.859331</Value></DefineArg>

    <DefineArg Name="Lat9"><Description>
        Latitude of waypoint 9 (default: SW).
    </Description><Units:degree/><Value>36.766</Value></DefineArg>

    <DefineArg Name="Lon9"><Description>
        Longitude of waypoint 9 (default: SW).
    </Description><Units:degree/><Value>-121.8649</Value></DefineArg>

    <DefineArg Name="Lat10"><Description>
        Latitude of waypoint 10 (default: S).
    </Description><Units:degree/><Value>36.769648</Value></DefineArg>

    <DefineArg Name="Lon10"><Description>
        Longitude of waypoint 10 (default: S).
    </Description><Units:degree/><Value>-121.848834</Value></DefineArg>

    <DefineArg Name="Lat11"><Description>
        Latitude of waypoint 11 (default: SE).
    </Description><Units:degree/><Value>36.7755</Value></DefineArg>

    <DefineArg Name="Lon11"><Description>
        Longitude of waypoint 11 (default: SE).
    </Description><Units:degree/><Value>-121.825</Value></DefineArg>

    <DefineArg Name="Lat12"><Description>
        Latitude of waypoint 12 (spare).
    </Description><Units:degree/><Value>NaN</Value></DefineArg>

    <DefineArg Name="Lon12"><Description>
        Longitude of waypoint 12 (spare).
    </Description><Units:degree/><Value>NaN</Value></DefineArg>

    <DefineArg Name="Speed"><Description>
        Vehicle speed for the entire mission.
    </Description><Units:meter_per_second/><Value>1</Value></DefineArg>

    <DefineArg Name="YoYoMinDepth"><Description>
        Minimum YoYo depth for the entire mission.
    </Description><Units:meter/><Value>5</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth1"><Description>
        Maximum YoYo depth during leg 1.
    </Description><Units:meter/><Value>20</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth2"><Description>
        Maximum YoYo depth during leg 2.
    </Description><Units:meter/><Value>25</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth3"><Description>
        Maximum YoYo depth during leg 3.
    </Description><Units:meter/><Value>100</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth4"><Description>
        Maximum YoYo depth during leg 4.
    </Description><Units:meter/><Value>70</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth5"><Description>
        Maximum YoYo depth during leg 5.
    </Description><Units:meter/><Value>65</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth6"><Description>
        Maximum YoYo depth during leg 6.
    </Description><Units:meter/><Value>45</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth7"><Description>
        Maximum YoYo depth during leg 7.
    </Description><Units:meter/><Value>45</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth8"><Description>
        Maximum YoYo depth during leg 8.
    </Description><Units:meter/><Value>100</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth9"><Description>
        Maximum YoYo depth during leg 9.
    </Description><Units:meter/><Value>65</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth10"><Description>
        Maximum YoYo depth during leg 10.
    </Description><Units:meter/><Value>50</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth11"><Description>
        Maximum YoYo depth during leg 11.
    </Description><Units:meter/><Value>20</Value></DefineArg>

    <DefineArg Name="YoYoMaxDepth12"><Description>
        Maximum YoYo depth during leg 12.
    </Description><Units:meter/><Value>20</Value></DefineArg>

    <DefineArg Name="YoYoMinAltitude"><Description>
        Minimum altitude while performing the YoYo behavior (for
        bottom-terminated YoYos).
    </Description><Units:meter/><Value>9</Value></DefineArg>

    <DefineArg Name="YoYoUpPitch"><Description>
        Vehicle up pitch while performing the YoYo behavior.
    </Description><Units:degree/><Value>20</Value></DefineArg>

    <DefineArg Name="YoYoDownPitch"><Description>
        Vehicle down pitch while performing the YoYo behavior.
    </Description><Units:degree/><Value>-20</Value></DefineArg>

<!-- You are even less likely to need to change these. -->

    <DefineArg Name="CaptureRadius"><Description>
        Waypoint capture radiues.
    </Description><Units:meter/><Value>NaN</Value></DefineArg>

    <DefineArg Name="MinAltitude"><Description>
        Minimum height above the sea floor for the entire mission.
    </Description><Units:meter/><Value>5</Value></DefineArg>

    <DefineArg Name="MaxDepth"><Description>
        Maximum depth for the entire mission.
    </Description><Units:meter/><Value>110</Value></DefineArg>

    <DefineArg Name="MinOffshore"><Description>
        Minimum offshore distance for the entire mission.
    </Description><Units:kilometer/><Value>2</Value></DefineArg>

    <DefineOutput Name="ElapsedSinceLastSampleStart"><Description>
        Mission variable (don't change). The mission sets this variable to reset
        the ESP sample timer.
    </Description><Units:minute/><Value>0</Value></DefineOutput>

    <DefineOutput Name="ElapsedTime"><Description>
        Mission variable (don't change). The mission sets this variable to reset
        the ESP sample timer.
    </Description><Units:hour/><Value>0</Value></DefineOutput>

    <DefineOutput Name="SampleInProgress"><Description>
        Mission variable (don't change). The mission sets this variable to while
        sampling is in progress.
    </Description><False/></DefineOutput>

<!-- Missions should almost always start with a timeout -->

    <Timeout Duration="MissionTimeout"/>

    <Insert Filename="Insert/Science.xml">
        <Description>
            Most missions will run the science sensors. If you don't place this
            aggregate above NeedComms, science instruments get turned off on the
            last upcast and while floating on the surface.
        </Description>
    </Insert>

<!-- Most missions should use the NeedComms aggregate. -->

    <Insert Filename="Insert/NeedComms.xml" Id="NeedComms"/>

    <Assign><Sequence/><Arg Name="NeedComms:DiveInterval"/><Arg Name="NeedCommsTime"/></Assign>

<!-- Missions should almost always start with standard safety envelopes;
                  most missions should not expose the parameters of these envelopes.
    -->

    <Insert Filename="Insert/StandardEnvelopes.xml"/>

    <Assign><Sequence/><Arg Name="StandardEnvelopes:MinAltitude"/><Arg Name="MinAltitude"/></Assign>

    <Assign><Sequence/><Arg Name="StandardEnvelopes:MaxDepth"/><Arg Name="MaxDepth"/></Assign>

    <Assign><Sequence/><Arg Name="StandardEnvelopes:MinOffshore"/><Arg Name="MinOffshore"/></Assign>

    <Assign><Sequence/><Arg Name="StandardEnvelopes:MaxDepth"/><Arg Name="MaxDepth"/></Assign>

    <Assign><Sequence/><Arg Name="StandardEnvelopes:MinOffshore"/><Arg Name="MinOffshore"/></Assign>

<!-- Sampling directives -->

    <Aggregate Id="CheckSamplingSettings">

        <Sequence/>

        <Syslog Severity="Info">Checking sampling settings.</Syslog>

        <Aggregate Id="CheckESP">

            <When>
                <Arg Name="SampleESP"/>
                <And><Not><Science:ESPComponent.loadAtStartup/></Not></And>
            </When>

            <Syslog Severity="Critical">Cannot service ESP sample request. ESPComponent is not loaded.</Syslog>

        </Aggregate>

        <Aggregate Id="CheckCANONSampler">

            <When>
                <Arg Name="SampleCANONSampler"/>
                <And><Not><Science:CANONSampler.loadAtStartup/></Not></And>
            </When>

            <Syslog Severity="Critical">Cannot service CANONSampler water sample request. CANONSampler component is not loaded.</Syslog>

        </Aggregate>

    </Aggregate>

    <Insert Filename="Insert/Sample.xml">
        <RedefineArg Name="SampleTimeout"><Arg Name="SampleTimeout"/></RedefineArg>
    </Insert>

<!-- Automatically cycle logs every 24 hours -->

    <Aggregate Id="CycleLogs">

        <Parallel/>

        <Aggregate>

            <Sequence/>

            <Guidance:Wait>
                <Sequence/>
                <Setting><Guidance:Wait.duration/><Units:hour/><Value>24</Value></Setting>
            </Guidance:Wait>

            <Syslog Severity="Important">Restarting logs.</Syslog>

            <Guidance:Execute>
                <Sequence/>
                <Setting><Guidance:Execute.command/><String>restart logs</String></Setting>
            </Guidance:Execute>

        </Aggregate>

    </Aggregate>

<!-- Acquire ESP sample every SampleInterval -->

    <Aggregate Id="SampleTimer">

        <While>
            <Arg Name="SampleInProgress"/>
            <Or><Elapsed><Arg Name="ElapsedSinceLastSampleStart"/></Elapsed><Gt><Arg Name="SampleInterval"/></Gt></Or>
        </While>

        <Aggregate Id="AcquireSample">

            <Sequence/>

            <Assign><Sequence/><Arg Name="ElapsedTime"/><Elapsed><Arg Name="ElapsedSinceLastSampleStart"/></Elapsed></Assign>

            <Syslog Severity="Important">Pre-sample comms. Elapsed time since last ESP sample: <Arg Name="ElapsedTime"/><Units:hour/></Syslog>

<!-- Surface for comms before initiating the sample sequence -->

            <Call Id="PreSampleComms" RefId="NeedComms"/>

<!-- Set the surface comms interval to the sample timeout to avoid interruptions while sampling -->

            <Assign><Sequence/><Arg Name="NeedComms:DiveInterval"/><Arg Name="SampleTimeout"/></Assign>

            <Aggregate Id="WaitForDepth">

                <Sequence/>

                <Break>
                    <Universal:depth/>
                    <Ge><Arg Name="YoYoMinDepth"/></Ge>
                </Break>

                <Syslog Severity="Info">Waiting to achieve min depth of <Arg Name="YoYoMinDepth"/><Units:meter/></Syslog>

                <Guidance:Wait>
                    <Sequence/>
                    <Setting><Guidance:Wait.duration/><Arg Name="SampleTimeout"/></Setting>
                </Guidance:Wait>

            </Aggregate>

<!-- Indicate a sample is in progress -->

            <Assign><Sequence/><Arg Name="SampleInProgress"/><True/></Assign>

<!-- This assignment restarts the sample timer -->

            <Assign><Sequence/><Arg Name="ElapsedSinceLastSampleStart"/><Value>0</Value></Assign>

<!-- Configure sampling sequance -->

            <Assign><Sequence/><Arg Name="Sample:SampleCANONSampler"/><Arg Name="SampleCANONSampler"/></Assign>

            <Assign><Sequence/><Arg Name="Sample:CANONSamplerDelay"/><Arg Name="CANONSamplerDelay"/></Assign>

            <Assign><Sequence/><Arg Name="Sample:ESPCartridgeType"/><Arg Name="CartridgeType"/></Assign>

            <Assign><Sequence/><Arg Name="Sample:SampleESP"/><Arg Name="SampleESP"/></Assign>

<!-- Trigger sampling sequance -->

            <Call Id="TriggerSample" RefId="Sample"/>

<!-- Surface for comms after the sampling sequence completes -->

            <Call Id="PreSampleComms" RefId="NeedComms"/>

<!-- Reinstate nominal surface comms interval -->

            <Assign><Sequence/><Arg Name="NeedComms:DiveInterval"/><Arg Name="NeedCommsTime"/></Assign>

            <Assign><Sequence/><Arg Name="SampleInProgress"/><False/></Assign>

        </Aggregate>

    </Aggregate>

    <Call Id="StartingMission" RefId="NeedComms"/>

<!-- Many missions will keep mass position and buoyancy volume fixed at defaults. -->

    <Guidance:Pitch>
        <Parallel/>
        <Setting><Guidance:Pitch.massPosition/><Control:VerticalControl.massDefault/></Setting>
    </Guidance:Pitch>

    <Guidance:Buoyancy>
        <Parallel/>
        <Setting><Guidance:Buoyancy.position/><Control:VerticalControl.buoyancyNeutral/></Setting>
    </Guidance:Buoyancy>

    <Guidance:SetSpeed>
        <Parallel/>
        <Setting><Guidance:SetSpeed.speed/><Arg Name="Speed"/></Setting>
    </Guidance:SetSpeed>

    <Guidance:DepthEnvelope>
        <Description>
            Another depth envelope for the YoYo behavior. This envelope should
            fall within the limits of the standard safety envelopes in
            Insert/StandardEnvelopes.xml in order to avoid commanding high pitch
            angles for depth-terminated YoYos.
        </Description>
        <Parallel/>
        <Setting><Guidance:DepthEnvelope.minDepth/><Arg Name="YoYoMinDepth"/></Setting>
        <Setting><Guidance:DepthEnvelope.downPitch/><Arg Name="YoYoDownPitch"/></Setting>
        <Setting><Guidance:DepthEnvelope.upPitch/><Arg Name="YoYoUpPitch"/></Setting>
    </Guidance:DepthEnvelope>

    <Guidance:AltitudeEnvelope>
        <Description>
            Another altitude envelope for the YoYo behavior. This envelope
            should fall within the limits of the standard safety envelopes in
            Insert/StandardEnvelopes.xml in order to avoid commanding high pitch
            angles for bottom-terminated YoYos.
        </Description>
        <Parallel/>
        <Setting><Guidance:AltitudeEnvelope.minAltitude/><Arg Name="YoYoMinAltitude"/></Setting>
        <Setting><Guidance:AltitudeEnvelope.upPitch/><Arg Name="YoYoUpPitch"/></Setting>
    </Guidance:AltitudeEnvelope>

    <Guidance:YoYo>
        <Parallel/>
        <Setting><Guidance:YoYo.downPitch/><Arg Name="YoYoDownPitch"/></Setting>
        <Setting><Guidance:YoYo.upPitch/><Arg Name="YoYoUpPitch"/></Setting>
    </Guidance:YoYo>

    <Aggregate Id="SetWaypointsPerLegParameter">

        <Description>
            The following Leg2-5 aggregates adjust the Lat[] and Lon[] variables
            according to the `trajectory` parameter:
        </Description>

        <Sequence/>

        <Aggregate Id="Leg2">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>1</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat1"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon1"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg3">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>2</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat2"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon2"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg4">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>3</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat3"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon3"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg5">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>4</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat4"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon4"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg6">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>5</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat5"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon5"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg7">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>6</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat6"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon6"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg8">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>7</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat7"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon7"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg9">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>8</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat8"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon8"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg10">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>9</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat9"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon9"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

        <Aggregate Id="Leg11">

            <Sequence/>

            <Break><Arg Name="leg"/>
                <Le><Units:count/><Value>10</Value></Le>
            </Break>

            <Assign><Sequence/><Arg Name="Lat10"/><Units:degree/><Value>NaN</Value></Assign>

            <Assign><Sequence/><Arg Name="Lon10"/><Units:degree/><Value>NaN</Value></Assign>

        </Aggregate>

    </Aggregate>

    <Aggregate Id="Lap">

        <Sequence/>

        <Syslog Severity="Important">Starting Lap</Syslog>

        <Syslog Severity="Important">Lat[1] = <Arg Name="Lat1"/><Units:degree/> Lon[1] = <Arg Name="Lon1"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[2] = <Arg Name="Lat2"/><Units:degree/> Lon[2] = <Arg Name="Lon2"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[3] = <Arg Name="Lat3"/><Units:degree/> Lon[3] = <Arg Name="Lon3"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[4] = <Arg Name="Lat4"/><Units:degree/> Lon[4] = <Arg Name="Lon4"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[5] = <Arg Name="Lat5"/><Units:degree/> Lon[5] = <Arg Name="Lon5"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[6] = <Arg Name="Lat6"/><Units:degree/> Lon[6] = <Arg Name="Lon6"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[7] = <Arg Name="Lat7"/><Units:degree/> Lon[7] = <Arg Name="Lon7"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[8] = <Arg Name="Lat8"/><Units:degree/> Lon[8] = <Arg Name="Lon8"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[9] = <Arg Name="Lat9"/><Units:degree/> Lon[9] = <Arg Name="Lon9"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[10] = <Arg Name="Lat10"/><Units:degree/> Lon[10] = <Arg Name="Lon10"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[11] = <Arg Name="Lat11"/><Units:degree/> Lon[11] = <Arg Name="Lon11"/><Units:degree/></Syslog>

        <Syslog Severity="Important">Lat[12] = <Arg Name="Lat12"/><Units:degree/> Lon[12] = <Arg Name="Lon12"/><Units:degree/></Syslog>

        <Aggregate Id="SampleOnStart">

            <Sequence/>

            <Break>
                <Not><Arg Name="StartWithASample"/></Not>
            </Break>

<!-- Kick off the first ESP sample. -->

            <Assign><Sequence/><Arg Name="SampleInProgress"/><True/></Assign>

        </Aggregate>

<!-- The following aggregates dispatch the waypoints behaviors -->

        <Aggregate Id="Wpt1">

            <Sequence/>

            <Syslog Severity="Important">Navigating to box start WP. YoYoMaxDepth:<Arg Name="YoYoMaxDepth1"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth1"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat1"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon1"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt2">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP2. YoYoMaxDepth: <Arg Name="YoYoMaxDepth2"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth2"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat2"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon2"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt3">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP3. YoYoMaxDepth: <Arg Name="YoYoMaxDepth3"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth3"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat3"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon3"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt4">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP4. YoYoMaxDepth: <Arg Name="YoYoMaxDepth4"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth4"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat4"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon4"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt5">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP5. YoYoMaxDepth:<Arg Name="YoYoMaxDepth5"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth5"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat5"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon5"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt6">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP6. YoYoMaxDepth:<Arg Name="YoYoMaxDepth6"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth6"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat6"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon6"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt7">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP7. YoYoMaxDepth: <Arg Name="YoYoMaxDepth7"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth7"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat7"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon7"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt8">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP8. YoYoMaxDepth: <Arg Name="YoYoMaxDepth8"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth8"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat8"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon8"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt9">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP9. YoYoMaxDepth: <Arg Name="YoYoMaxDepth9"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth9"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat9"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon9"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt10">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP10. YoYoMaxDepth: <Arg Name="YoYoMaxDepth10"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth10"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat10"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon10"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt11">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP11. YoYoMaxDepth: <Arg Name="YoYoMaxDepth11"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth11"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat11"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon11"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

        <Aggregate Id="Wpt12">

            <Sequence/>

            <Syslog Severity="Important">Navigating to WP12. YoYoMaxDepth: <Arg Name="YoYoMaxDepth12"/><Units:meter/></Syslog>

            <Guidance:DepthEnvelope>
                <Setting><Guidance:DepthEnvelope.maxDepth/><Arg Name="YoYoMaxDepth12"/></Setting>
            </Guidance:DepthEnvelope>

            <Guidance:Waypoint>
                <Sequence/>
                <Setting><Guidance:Waypoint.latitude/><Arg Name="Lat12"/></Setting>
                <Setting><Guidance:Waypoint.longitude/><Arg Name="Lon12"/></Setting>
            </Guidance:Waypoint>

        </Aggregate>

    </Aggregate>

</Mission>